background image

19.2 VOLT CORDLESS DRILL

OWNER’S MANUAL

Item Number W50092

WARNING

It is the owner and/or operators’ responsibility to study all WARNINGS, operating, and maintenance 
instructions contained on the product label and instruction manual prior to operation of this product. 
The owner/operator shall retain product instructions for future reference.

The owner and/or operator are responsible for maintenance, maintaining all decals or warning 
labels and while in use, maintaining the unit in good working order. If the owner and/or operator 
are not fluent in English, the product warnings and instructions shall be read and discussed with 
the operators’ native language by the purchaser/owner or his designee. Make sure that the 
operator comprehends its contents. Safety information shall be emphasized and understood 
prior to usage. The product shall be inspected per the operating instructions.

Users of this product must fully understand these instructions. Each person operating this 
product must also be of sound mind and body and must not be under the influence of any 
substance that might impair their vision, dexterity or judgment.

Protect yourself and others by observing all safety information.

Failure to comply with instructions could result in personal injury and/or property damage! 

Summary of Contents for W50092









Reviews: