RIVETING CHAIN PINS CONT.
8. Tighten the push bolt by hand using the lever or a 14-mm
wrench until the rivet tip spreads the hollow nose
of the chain pin. Now the end of the chain pin should be flared
over the side plate just enough so the side
plate is solidly held in place. Repeat this procedure on the other
chain pin.
9. Remove the tool from the chain. Verify both chain pins show the
same size flares. Verify the riveted-on
side plate is aligned with the side plates of the adjacent chain
links.
PRESSING SIDE PLATES
1. Thread the alignment bolt into the C-frame.
2. Assemble the press plates into the tool. Place the grooved press
plate into the hole in the C-frame; insert the other press plate
into the alignment bolt.
3. Verify the chain pins are aligned with the groove and holes in the
press plates.
4. Use a 14-mm wrench to tighten the alignment bolt until chain
pins protrude past the face of the side plate.
Clip-type Master Links
The pins must protrude enough to install the clip into the grooves
in the chain pin.
Rivet-type Master Links
The pins must protrude enough to be flared over the side plate.
Refer to the chain manufacturer’s specifications for chain pin protrusion as
well as the direction and installation of master link clips.
RIVETING CHAIN PINS
1. Thread the alignment bolt into the C-frame.
2. Insert the rivet tip into the spring and slide them both into the
alignment bolt.
3. Thread the push bolt into the alignment bolt above the tip.
4. Place the large anvil in the hole in the C-frame.
5. Place the tool over the chain pin to be riveted, with the hollow
end of the chain pin facing the rivet tip.
NOTE: The small anvil is used for cam chains up to the 3-series.
6. Verify the rivet tip is withdrawn enough to clear the end of the
chain pin.
7. Tighten the alignment bolt securely against the side plate of the
chain pin.
5
4
LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These
warranties give specific legal rights. Except where prohibited by local law, the law of the State of Washington
governs all warranties and all exclusions and limitations of warranties and remedies. There may be other rights
which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal
use and service. A defective product may be returned for a free replacement within 90 days from the date of
purchase, provided that product is returned to place of purchase immediately after discovery of defect. After 90
days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge any parts which
our examination shall disclose to be defective and under warranty. These warranties shall be valid only when a sales
receipt showing the date of purchase accompanies the defective product or defective part (s) being returned. For
part (s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be
replaced under normal use and service. These warranties shall not apply to any product or part which is used for a
purpose for which it is not designed, or which has been repaired or altered in any way so as to affect adversely its
performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse,
neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in
connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no
express or implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes
no implied warranty of merchantability and no implied warranty of fitness for any particular purpose, except that for
goods purchased primarily for personal, family or household use and not for commercial or business use,
PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied
warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the
duration, expressly warranted above.
The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in
all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any
manner related to any product, or to the design, use, or any inability to use the product. The sole and exclusive
remedy for a defective product or part shall be the repair, or replacement thereof as provided above. The laws on
limitation of remedies or on consequential, incidental or special damages may vary from state to state, so the above
limitations may not apply in all cases.
© Copyright 2015 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138
6
