background image

Form No. Z2025A

Rev. 12.05.03

INSTALLATION AND OPERATION INSTRUCTIONS

DIRECT DRAW DISPENSER - SELF-CONTAINED MODELS

Table of Contents

PREPARING THE CABINET FOR USE
Specifications.........................................................2
List of Included Parts.............................................3
Tools Required.......................................................3
Plumbing................................................................3
Electrical ................................................................3
Installing Casters or Legs......................................3
Installing Faucet and Standard..............................3
TAPPING
Connecting the Keg Coupler .................................4
Tapping the Keg.....................................................4
Connecting the Regulator......................................5
Adjusting Gas Flow................................................5
CO

2

Leak Test .......................................................5

Replacing a CO

2

Gas Cylinder..............................5

Handling CO

2

Gas .................................................5

TEMPERATURE
Beer Temperature ..................................................6
Refrigeration and Temperature Control .................6
CLEANING
Cleaning the Beer Lines ........................................7
Cleaning the Cabinet .............................................7
GENERAL INFORMATION
How to Pour a Perfect Glass of Beer ....................8
Troubleshooting .....................................................9
Beer Facts .............................................................9
REPLACEMENT PARTS ................................10-11
Wiring Diagram ....................................................12

8300 West Good Hope Road  •  Milwaukee, WI 53223  •  Phone 414-353-7060  •  Fax 414-353-7069

Toll Free 800-558-5592  •  E-Mail: Perlick@Perlick.com  •  www.Perlick.com

MODEL NOS.

DS Series

IMPORTANT INFORMATION

Fill out the enclosed warranty card and mail to the
Perlick Corporation to register the warranty. If the
card is not returned, the warranty period will begin
from the date the equipment is shipped from the 
factory.

This manual has been prepared to assist you in the
installation of your Direct Draw Dispenser and to
acquaint you with its operation and maintenance.

We dedicate considerable time to ensure that our
products provide the highest level of customer 
satisfaction. If service is required, your dealer can
provide you with a list of qualified service agents. For
your own protection, never return merchandise for
credit without our approval.

We thank you for selecting a Perlick product and
assure you of our continuing interest in your
satisfaction.

WARNING: When lifting, the full weight of the
cabinet must be supported. Lift from the cabinet
base and not from the top. Improper lifting can
result in severe damage to the cabinet.

Summary of Contents for DS Series













Reviews: