background image

Perlight Solar PLM-OM Series Installation Manual

3

www.perlight.com

V.01.2022 A1.0

1. Introduction

This installation manual specifies the installation and maintenance requirements for 

crystalline silicon PV modules (“solar modules”) manufactured by Perlight Solar Co., Ltd.

This installation manual is intended for the installation and maintenance of solar modules, 

and helps customers to correctly install the photovoltaic power generation system. This 

installation manual does not apply to the installation of the Perlight double glass modules and 

conventional modules. Please read this manual carefully prior to handling and installation. 

This manual contains important electrical and mechanical installation information. For correct 

installation, stable power output, installation and maintenance of the solar modules, carefully 

read and understand all installation instructions in the manual. Keep this manual in a safe 

place for future reference (care and maintenance) and in case of sale or disposal of the solar 

modules. This manual does not constitute a warranty, expressed or implied. Perlight does not 

assume responsibility and expressly disclaims liability for loss, damage, or expense arising 

out of or in any way connected with installation, operation, use or maintenance of the solar 

modules.

The mechanical and electrical installation of the solar modules shall be made in accordance 

with applicable laws and regulations, including electrical, construction and electrical 

connection requirements. These regulations vary depending on the installation site, such as 

building roofs, surface mounts, in-vehicle applications, and so on. The requirements may vary 

depending on the installation system voltage, the use of DC or AC. Please refer to the relevant 

local laws and regulations.

Installation and maintenance of Perlight Solar modules may only be carried out by trained and 

qualified personnel. If you require further information, contact your supplier or local Perlight 

Service Centre. 

Please provide a copy of this manual to the owner and operator of the PV system for 

reference.

Thank you for choosing Perlight Solar PV modules.

Summary of Contents for PLM-OM Series




















Reviews: