www.petsafe.net 7
Risk of explosion if batteries are replaced by
an incorrect type. Do not short circuit, mix
old and new batteries, dispose of in fire, or
expose to water. When batteries are stored
or disposed, they must be protected from
shorting. Dispose of used batteries properly.
3. Prepare the hopper. Open the lid by pressing the Lid Release Button on the front of the AutoTrainer:
A. Select the appropriate sized Food Disk and insert it into the Food Hopper. Twist to the left to lock.
To unlock a Food Disk, twist it to the right.
B. Insert your dog's daily amount of kibble into the food hopper. The Food Hopper can hold
approximately 3.5 cups of medium-sized kibble. Be sure to feed your pet their entire
recommended daily serving of kibble each day. Servings over 3.5 cups may need to be given
separately, once the AutoTrainer has been turned off.
Operating the AutoTrainer
1. Turn the AutoTrainer Base Unit on by pressing
down the Power button (
2A) for 3 seconds.
2. Turn the power for the AutoTrainer Collar on
to synchronize with the AutoTrainer Base Unit.
Move from 0 - I to power on (
2B). A red LED
light will turn on for a few moments, then off
again (
2C). When the AutoTrainer detects the
AutoTrainer Collar’s signal, an arrow will appear
over the AutoTrainer Collar signal icon (
2D). If
the AutoTrainer Collar loses connection with
the AutoTrainer Base Unit as indicated on the
LCD screen, restart the AutoTrainer Collar and
AutoTrainer Base Unit at the same time while
pressing the ID button on the AutoTrainer Collar
(
2E) with the tip of a paper clip (or similar item)
for 2 seconds. The ID will update immediately
and the LCD will show an arrow over the
AutoTrainer Collar icon (
2D).
3. To change modes, press the Mode key within
7 seconds of powering on the AutoTrainer
Base Unit. The AutoTrainer Base Unit will
begin Calm Me mode if no buttons have been
pressed for 7 seconds. Hold the Power button
for one second to start immediately.
4. An arrow will indicate which mode is active (2F).
No mode will begin until the AutoTrainer Collar unit is connected to the
AutoTrainer Base Unit.
5. Adjust the volume by pressing the Volume key (VOL). The volume icon on
the top right of the screen (
2G) will indicate what level is selected. There
are three volume levels.
6
Customer Care Center 1-800-732-2677
Tone(s): The sounds emitted by the AutoTrainer Base Unit
Display:
Collar Signal (icon): An icon displayed to alert the connection of the AutoTrainer Collar Unit to the
AutoTrainer Base unit, as indicated by the icon on the display screen.
Barks: The number of Barks recorded
Barks Per Hour: The number of barks recorded per hour
Scan: Assists with selection of modes and viewing of history
Vol: Volume control button
Food: Amount of food dispensed during a session
Mode: Press to select Teach Me or Calm Me modes. Press to Pause and Un-Pause
Teach Me Mode: A series of sequences, the introductory mode that prepares the dog for Calm Me mode.
This mode teaches your dog to associate the tones with food delivery and associate other behaviors
(barking, pawing the machine) with an “Uh-Oh” tone.
Calm Me Mode: This mode continues to play the series of sequences from Teach Me mode, however,
when the dog barks or moves the machine, the “Uh-Oh” tone restarts the sequence and delays the delivery
of food. This mode teaches the dog that they will be rewarded for quiet behavior.
Operating Guide
If your dog has special dietary needs, consult your veterinarian before using this
product. Please use with dry food only. Kibble size should not exceed ¼ inch for Small
Food Disk and ½ inch for Large Food Disk.
The AutoTrainer Collar is not guaranteed to fit properly on dogs under 10 lbs.
Preparing the AutoTrainer
1. Remove the Food Dish Attachment from the bottom of the AutoTrainer Base Unit (1A) and attach it
to the front of the AutoTrainer (
1B). Be sure to lock it in securely so the Muzzle Detector and Food
Dispenser are not blocked. Place the Food Dish securely inside of the Food Dish Attachment.
2. Install 4 D batteries into the battery compartment, located on the bottom of the AutoTrainer Base Unit
(
1C). An AC Power Adapter is provided as an alternative way to power the AutoTrainer Base Unit. On
the AutoTrainer Collar, insert two CR2032 batteries, positive side up, into the battery compartment (
1D).
Replacement batteries (3-volt, CR2032) can be found at many retailers.
1A
1B
1C
1D
2B
2A
2D
2C
2E
2G
2F