Petsafe Elite Pendant PDT00-13377 Operating And Training Manual Download

Page: 5 / 28

www.petsafe.net 5

The Pendant

™

Receiver can be used with most collars up to ¾” wide

Rechargeable batteries in the Handheld Remote and Pendant

™

Receiver

Waterproof Pendant

™

Receiver and water-resistant Handheld Remote

Key Definitions

Handheld Remote: Transmits the signal to the Pendant

™

Receiver.

Slide Switch: Adjusts the stimulation range to 1 of 3 positions, low, medium, or high.
Stimulation Button 1: Delivers continuous stimulation

up to 10 seconds long. Low stimulation.
Stimulation Button 2: Delivers continuous stimulation

up to 10 seconds long. Medium stimulation.
Stimulation Button 3: Delivers continuous stimulation

up to 10 seconds long. High stimulation. Note: When a

stimulation button is held for 10 seconds or more, the

Handheld Remote will “time-out.” The button will need

to be released for 5 seconds and pressed again before

additional stimulation can be delivered.
Tone Button: Produces an audible tone from the collar.

No stimulation is delivered.
Status Gauge: Displays battery life, charging status,

and when a tone (green) or stimulation (yellow) button is

being pressed.
Micro USB Port: Connects to myTrainer

™

software. Also

used to connect Power Adapter for charging. Keep the

cover in place when not charging to keep debris out of

the opening.
Pendant

™

Receiver: Delivers stimulation or tone on

a signal from the Handheld Remote. The Pendant

™

waterproof.
SmartTouch On/Off Buttons: Momentarily pressing and

holding these buttons simultaneously turns the Pendant

™

on and off.
Contact Loops: The contacts through which the Pendant

™

delivers stimulation.
Status Gauge: Displays battery life, charging status,

and when a tone (green) or stimulation (yellow) button is

being pressed.
Micro USB Port: Connects to myTrainer

™

software. Also

used to connect Power Adapter for charging. Keep the

cover in place when not charging to keep debris out of

the opening.

Slide Switch

(Low, Med, High)

Status

Gauge

Stimulation

Buttons

1 2 3

Tone Button

Contact Loops

Status

Gauge

Micro USB Port

(with cover)

Contact Loops

SmartTouch

On/Off

SmartTouch

On/Off

Summary of Contents for Elite Pendant PDT00-13377





























Search results

Summary of Contents for Elite Pendant PDT00-13377

Reviews:

Related manuals for Elite Pendant PDT00-13377

Brands by name

Popular brands

Petsafe Elite Pendant PDT00-13377, Operating And Training Manual

Search results

Summary of Contents for Elite Pendant PDT00-13377

Reviews:

Related manuals for Elite Pendant PDT00-13377

Brands by name

Popular brands