3
2
EN
Nomenclature
(1) Sensor, (2) Narrow beam white LED, (2 bis) Wide beam
white LED, (3) Selector knob, (4) ZEPHYR band, (5) Cable, (6)
Rechargeable battery case, (6 bis) Rechargeable battery, (7)
Rechargeable battery USB connector, (8) Rear plate, (9) Energy
gauge, (10) USB cable, (11) Top strap, (12) Red LED, (13) Bluetooth
activation indicator (blue).
REACTIVE LIGHTING technology
The lamp features REACTIVE LIGHTING technology. The lamp’s
integrated light sensor instantly and automatically adapts the shape
and power of the beam. REACTIVE LIGHTING technology gives you
the benefit of optimal lighting for your activities.
For biking, use your lamp with CONSTANT LIGHTING technology
(risk of switching off with REACTIVE LIGHTING technology).
Before the first use of your lamp
1. Connect the rechargeable battery.
2. Charge the battery completely
The rechargeable battery is delivered with a 30 % charge.
3. Connect the rechargeable battery case.
Lamp operation
Switching on & off, selecting
The knob works in two ways:
- short pulse: turn and release,
- long hold: turn, hold several seconds depending on the desired
function, then release.
When you turn on the light, it automatically lights up in REACTIVE
LIGHTING mode. When switching between REACTIVE and
CONSTANT technologies, the lamp always turns on in MAX
AUTONOMY mode.
In REACTIVE LIGHTING mode, when the sensor detects an area
with sufficient light, your lamp will blink dimly for two minutes, then
automatically turn off to conserve rechargeable battery life.
Attention: the rear red light, steady or strobe, is activated and
deactivated only via the MyPetzl Light app.
Attention, the LOCK position does not turn off the lamp: be sure to
turn it off before using the LOCK.
MyPetzl Light Bluetooth
®
mobile app - customizing
your lamp.
Downloading the MyPetzl Light app, and Bluetooth
®
linkage.
Access to the battery’s charge level; to the lamp’s remaining burn
time; to controlling the red light and to customizing lamp performance
depending on the activities, according to four preset profiles: trail
running, mountaineering, trekking and camping/backpacking.
By default, the lamp comes with Bluetooth
®
activated.
The Bluetooth
®
mark and logo are registered trademarks of Bluetooth
SIG Incorporated and are used under license by Petzl.
Attention: requires iOS 7 or later, Android 4.3 or later and Bluetooth
®
4 or later.
Restore initial settings
Restore the initial Petzl settings by a long hold of 30 seconds, with
the lamp turned off.
Charging the rechargeable battery
The lamp comes with a Petzl Li-Ion rechargeable battery. Capacity:
2600 mAh
Charge it completely before the first use.
Use only a Petzl ACCU NAO + rechargeable battery.
In general, Li-Ion rechargeable batteries lose 10 % of their capacity
each year. After 300 charge/discharge cycles, they still have about
70 % of their initial capacity.
Warning, though this lamp is constructed of high quality plastics, they
can become brittle at extreme temperatures.
Charging the battery
Recharge only with a USB cable of less than 3 meters in length. The
charger’s output voltage must not exceed 5 V. Use only a CE/UL
approved charger.
The USB external power supply connected to your product must be
a SELV type and be a limited power source as defined in chapters
2.2 and 2.5 of the standards IEC 60950-1 ed.2.2 and EN 60950-1 :
2006+A11 : 2009+A1 : 2010+A12 : 2011+A2 : 2013.
When charging, the power plug should remain easily accessible.
It is recommended to regularly charge your rechargeable battery
completely in order to optimize the lamp’s performance.
Recharge time
Recharge time is 6 hours with the USB charger, or a computer.
Attention, if many USB devices are connected to your computer, the
charging time can increase (up to 24 hours).
During charging, the three bars on the energy gauge will blink.
Charging is done when the three bars are lit.
Energy gauge
The energy gauge lights for 10 seconds when your lamp is switched
on or off.
When the last bar begins to blink, the lamp emits a light signal to
indicate that it is in reserve mode (approximately 1 hour).
Replacing the rechargeable battery
Use only a Petzl ACCU NAO + rechargeable battery. Using another
type of rechargeable battery can damage your lamp. Do not use
another type of rechargeable battery.
Attention, when you unplug and then plug-in a rechargeable battery
(only when changing the battery stick itself), do a complete recharge
to reset the energy gauge.
Do not combine components from different generations
(lamp case, battery case and rechargeable battery), as
this can degrade your lamp’s performance.
General info on Petzl lamps and
batteries
A. Rechargeable battery precautions
Warning, incorrect use can damage the rechargeable battery.
- Do not submerge the rechargeable battery in water.
- Do not put the rechargeable battery in a fire.
- Do not destroy the rechargeable battery, it can explode or release
toxic materials.
- If your rechargeable battery is damaged, do not dismantle it or
change its structure.
- If your rechargeable battery is deformed or cracked, dispose of it
in a recycling bin.
B. Lamp precautions
Warning: powerful lamp - risk of high heat or burning.
The lamp is not recommended for children.
Eye safety
The lamp is classified in risk group 2 (moderate risk) according to the
IEC 62471 standard.
- Do not look directly at the lamp when lit.
- The optical radiation emitted by the lamp can be dangerous. Avoid
aiming the lamp’s beam into another person’s eyes.
- Risk of retinal damage from the emission of blue light, particularly
in children.
Electromagnetic compatibility
Meets the requirements of the 2004/108/CE directive on
electromagnetic compatibility.
Warning, an avalanche beacon in receive (find) mode can experience
interference when in proximity to your headlamp. In case of
interference (indicated by static noise from the beacon), move the
beacon away from the headlamp.
C. Cleaning, drying
If used in a damp environment, remove the battery from the lamp and
dry the lamp case with the USB port cover open. In case of contact
with seawater, rinse the lamp in fresh water and dry it.
If your lamp is dirty, clean it with a damp cloth and let it dry.
Do not allow chemicals to come into contact with your lamp.
D. Storage
For storage or transport, unplug the cable from the rechargeable
battery case on your lamp. For prolonged storage, recharge your
battery until the energy gauge has two bars lit, then unplug the
battery case (repeat this every three months). Be sure to store your
rechargeable battery in a dry place. The ideal storage temperature is
between 20 and 25° C. After 12 months in these conditions without
use, the rechargeable battery will be discharged. Avoid allowing your
rechargeable battery to discharge completely.
E. Protecting the environment
F. Modifications/repairs
Prohibited outside of Petzl facilities, except replacement parts.
G. Questions/contact
The Petzl guarantee
This lamp is guaranteed for 3 years against any defects in
materials or manufacture (except the rechargeable battery, which
is guaranteed for one year or 300 cycles). Exclusions from the
guarantee: more than 300 charge/discharge cycles, normal wear
and tear, oxidation, modifications or alterations, incorrect storage,
poor maintenance, damage due to accidents, to negligence, or to
improper or incorrect usage.
Responsibility
Petzl is not responsible for the consequences, direct, indirect or
accidental, or any other type of damage befalling or resulting from the
use of its products.
Marking
(a) Model.
(b) Rechargeable battery serial number.
(c) International certifying bodies.
(d) Turning on or off.
(e) Conforms to European requirements: Petzl declares that this
product conforms to the essential requirements and other relevant
provisions of the 1999/5/CE, 2004/108/CE, 2006/95/CE Directive.
The declaration of conformity can be found at Petzl.com
(f) Product designed and manufactured with high quality materials
and components that can be recycled and reused.
(g) Management of electrical and electronic equipment waste.
(h) Made in.
FCC/IC informations
The device complies with FCC and IC radiation exposure limits set
forth for general population. This device must not be co-located or
operating in conjunction with any other antenna or transmitter.
The device complies with Part 15 of the FCC Rules and with Industry
Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions : (1) this device may not cause harmful
interference, and (2) this device must accept any interference,
including interference that may cause undesired operation. Note :
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception which can be determined by turning the equipment off and
on, the user is encouraged to try to correct interference by one or
more of the following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio /TV technician for help.
IC
: Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful
communication.
FR
Nomenclature
(1) Capteur, (2) Led blanche du faisceau pointu, (2 bis) Led blanche
du faisceau large, (3) Bouton sélecteur, (4) Bandeau ZEPHYR,
(5) Câble, (6) Boîtier de la batterie rechargeable, (6 bis) Batterie
rechargeable (7) Connecteur USB batterie rechargeable, (8) Platine
arrière, (9) Jauge d’énergie, (10) Rallonge USB, (11) Bandeau
supérieur, (12) Led rouge, (13) Témoin bleu d’activation du Bluetooth.
Technologie REACTIVE LIGHTING
La lampe dispose de la technologie REACTIVE LIGHTING. La
forme et la puissance du faisceau sont adaptées instantanément, et
automatiquement, grâce au capteur de luminosité intégré à la lampe.
La technologie REACTIVE LIGHTING vous permet de
bénéficier d’un confort d’éclairage optimum au cours
de vos activités.
À vélo, utilisez votre lampe avec la technologie
CONSTANT LIGHTING (risque d’extinction avec la
technologie REACTIVE LIGHTING).
Avant la première utilisation de
votre lampe
1. Connectez la batterie rechargeable.
2. Chargez complètement la batterie.
La batterie rechargeable est livrée chargée à 30 %.
3. Connectez le boîtier de la batterie rechargeable.
Fonctionnement de votre lampe
Allumer, éteindre, sélectionner
Le bouton fonctionne de deux façons :
- impulsion courte : tournez puis relâchez,
- appui long : tournez, maintenez plusieurs secondes selon la
fonction recherchée, puis relâchez.
Lorsque vous allumez votre lampe, elle s’allume systématiquement
en mode technologie REACTIVE LIGHTING. Lors du passage aux
technologies REACTIVE ou CONSTANT, la lampe s’allume toujours
sur le mode MAX AUTONOMY.
En mode technologie REACTIVE LIGHTING, lorsque le capteur
de la lampe détecte un milieu suffisamment éclairé, votre lampe
émet un clignotement faible pendant deux minutes, puis s’éteint
automatiquement pour préserver l’autonomie de la batterie
rechargeable.
Attention, l’éclairage rouge à l’arrière, fixe ou clignotant, s’active et
se désactive uniquement via l’application MyPetzl Light.
Attention, la position LOCK n’éteint pas votre lampe : veillez à
l’éteindre avant de la mettre en LOCK.
Application mobile Bluetooth® MyPetzl Light -
personnalisation de votre lampe
Téléchargement de l’application MyPetzl Light et couplage
Bluetooth®.
Accès au niveau de la charge de la batterie, à l’autonomie restante
de la lampe, à la gestion de l’éclairage rouge et à la personnalisation
des performances de la lampe en fonction des activités selon quatre
profils prédéfinis : trail running, alpinisme, trekking et camping/
bivouac, à la gestion de l’éclairage rouge à l’arrière.
La lampe est livrée, par défaut, avec le Bluetooth® activé.
La marque et le logo Bluetooth® sont des marques déposées de
Bluetooth SIG, Inc., et leur utilisation par Petzl fait l’objet d’un accord
de licence.
Attention : nécessite iOS supérieur ou égal 7 et Android supérieur ou
égal 4.3, et Bluetooth® supérieur ou égal à 4.
Retour à la configuration initiale
La configuration initiale Petzl est retrouvée par un appui long de 30
secondes, lampe éteinte.
Batterie rechargeable - charge
La lampe est dotée d’une batterie rechargeable Li-Ion Petzl. Capacité
: 2600 mAh.
Rechargez-la complètement avant la première utilisation.
Utilisez uniquement une batterie rechargeable ACCU NAO+ Petzl.
De manière générale, les batteries rechargeables Li-Ion perdent 10 %
de leur capacité par an. Au bout de 300 cycles de charge/décharge,
elles ont encore environ 70 % de leur capacité initiale.
Attention, bien que cette lampe soit conçue avec des plastiques de
haute qualité, ils peuvent être fragilisés à des températures extrêmes.
Charge de la batterie
Rechargez uniquement par un câble USB d’une longueur inférieure à
trois mètres. La tension délivrée par le chargeur ne doit pas dépasser
5 V. Utilisez uniquement un chargeur homologué CE/UL.
L’alimentation externe USB connectée à votre produit doit être de
type TBTS et être une Source à Puissance Limitée au sens des
chapitres 2.2 et 2.5 des normes IEC 60950-1 ed.2.2 et EN60950-
1:2006+A11:2009+A1:2010+A12:2011+A2:2013.
Lors de la recharge, la fiche de prise de courant doit rester aisément
accessible.
Il est conseillé d’effectuer régulièrement une charge complète
de votre batterie rechargeable afin d’optimiser au mieux les
performances de votre lampe.
