PEUGEOT ENERGYSand-100, User Manual

4

5

4

5

setting the tool

5.  Push the belt by hand and check to see if the 

sanding belt tends to run to one side or the 

other on the two drums.

6.  If the sanding belt runs toward disc, slightly 

turn the tracking knob (6) counterclockwise.

7.  If the sanding belt runs away from the disc, 

slightly turn the tracking knob (6) clockwise.

8.  Plug sander into power source and turn the 

switch ON and OFF quickly, and check to 

see if the sanding belt moves to either side. 

Re-adjust and fine tune tracking knob if 

necessary.

9.  When proper tracking is achieved, replace 

dust chute (2).

changing Position of sanDing belt 

table

sanding table in vertical position (fig. 15, 16)

note: 

The sanding table (1) can be used in 

either the horizontal or vertical position. 

1.  To move the sanding table (1), loosen the two 

bolts (2) with the supplied wrench (3) from the 

slots of the side pulley cover that attach table 

to the main body. 

2.  Move the sanding table (1) to the desired 

position. 

3.  Tighten the two bolts (2).

4.  Remove the disc/belt table and rod (3) from 

the sanding disc area by removing the hex 

bolt near base. (Fig. 16)

5.  Place the hex bolt (4) into the threaded hole 

near the auxiliary hole.

6.  Slide the rod (3) into the auxiliary hole for the 

belt table (5) until the table is 1.59 mm from 

sanding belt. (Fig. 16)

7.  Align flat surface onto support rod with hex 

bolt (6) on table bracket and tighten the bolt 

(6).

leveling the arM (fig. 17)

A positive table stop (4) is provided to position 

the sanding table level with workbench when the 

table is in the horizontal position.

1.  Place the sanding table (1) in the horizontal 

position.

2.  Place a level (2) on the sanding belt and 

check to see if the table is level.

3.  If an adjustment is necessary, loosen lock 

nut (3), and turn the sanding table stop (4) 

clockwise to raise, or counterclockwise to 

lower, until the sanding table is level. 

4.  Tighten the lock nut (3).

aDjUsting Disc table sqUare with 

sanDing Disc (fig. 11)

1.  Using a combination square (1), place one 

side of the square on the disc table assembly 

(2) with the other side against the sanding 

disc (3), and check to see if the disc table is 

90° to the disc.

2.  If the disc table surface is not 90° to the disc, 

loosen the table lock knob (4), adjust table 

square with disc and tighten the table lock 

knob (4).

3.  Adjust pointer (5) to the 0° mark on the angle 

scale using a screwdriver.

aDjUsting Disc table angle (fig. 12)

1.  The disc table (1) can be tilted from 0° to 45° 

by loosening the table lock knob (2).

2.  Tilt the disc table (1) to the desired angle. 

3.  Tighten table lock knob (2).

rePlacing sanDing belt anD tracking 

belt (fig. 13, 14)

1.  Remove the dust chute (2) from belt by 

loosening the two screws (1) (Fig. 13).

2.  Slide tension lever (3) to the right to release 

tension on the sanding belt (4). (Fig. 14)

3.  Remove sanding belt from both sanding 

drums (5).

4.  Slide new sanding belt over sanding drums. 

Making sure the belt arrow located on the 

inside of the belt will run in the right direction. 

Slide tension lever (3) to the left to apply belt 

tension.

warning! to avoid injury, always keep the 

plug disconnected from the power source 

and the switch turned off until the sander is 

completely assembled and adjusted properly.

warning! to avoid trapping the workpiece 

or fingers between the table and sanding 

disc, the disc table edge should positioned 

a maximum of 1.59 mm from sanding disc 

plate.

warning! after tilting the table, the assembly 

must be repositioned on the support rod by 

loosening the bolt (3) to a maximum of 1.59 

mm distance between the sanding disc and 

the edge of the disc table, to avoid trapping 

the work or finger between the disc and disc 

table.

warning! to avoid injury, turn switch off 

and disconnect the plug from the power 

source before removing and installing 

sanding belt.

warning! to avoid trapping the workpiece 

or fingers between the table and sanding 

belt, the table edge should be positioned a 

maximum of 1.59 mm from sanding belt.