background image

 


 

Read all instructions before using the Wine cooler.   
• DANGER or WARNING:     

Risk of child entrapment.       
Child entrapment and suffocation are not problems of the past. Junked or abandoned 
appliances are still dangerous . . . even if they will “just sit in the garage a few days”. 
   
Before you throw away your old Wine cooler: Take off the door.     
Leave the shelves in place so that children may not easily climb inside. Never allow 
children to operate, play with, or crawl inside the appliance. Never clean appliance parts 
with flammable fluids. The fumes can create a fire hazard or explosion. Do not store or 
use gasoline or any other flammable vapors and liquids in the vicinity of this or any other 
appliance. The fumes can create a fire hazard or explosion.   
   

-Save these instructions-

 

 

 

Ø

 

Before Using Your Wine Cooler 

 

Remove the exterior and interior packing. • Before connecting the Wine Cooler to the power 
source,  let  it  stand  upright  for  approximately  2  hours.  This  will  reduce  the  possibility  of  a 
malfunction in the cooling system from handling during transportation. • Clean the interior 
surface with lukewarm water using a soft cloth. • When replace the illuminating lamp, please 
select  the  lamp  which  comply  with  the  rated  power  input  of  lamp  according  to  the  rating 
label. Shut off the power supply before replacing the lamp. • When disposing your appliance, 
please choose an authorized disposal site.   

 

Installation of Your Wine Cooler 

• Place your Wine Cooler on a floor / surface that is strong enough to support it when it is 
fully  loaded.  To  level  your  Wine  Cooler,  adjust  the  leveling  leg  at  the  bottom  of  the  Wine 
Cooler.  •  Locate  the  Wine  Cooler  away  from  direct  sunlight  and  sources  of  heat  (stove, 
heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may 
increase  electrical  consumption.  Extreme  cold  ambient  temperatures  may  also  cause  the 
unit not to perform properly. • Avoid locating the unit in moist areas.• Plug the Wine Cooler 
into an exclusive, properly installed wall outlet. Any questions concerning power should be 
directed toward a certified electrician or an authorized Products service center.   

 

Attention 

Store wine in sealed bottles. Do not overload the cabinet. Do not open the door unless 
necessary. Do not cover shelves with aluminum foil or any other shelf material which may 

Summary of Contents for P120

















Reviews: