4
INSTALLATION INSTRUCTIONS
➢
Before Using Your Wine cooler
•
Remove the exterior and interior packing.
•
Before connecting the Wine cooler to the power source, let it stand upright for
approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system
from handling during transportation.
•
Clean the interior surface with lukewarm water using a soft cloth.
•
This appliance is intended to be used in household and similar applications such as
– staff kitchen areas in shops, offices, and other working environments.
– farmhouses and by clients in hotels, motels, and other residential type environments.
– bed and breakfast type environments.
–
catering and similar non-retail applications.
•
When disposing your appliance, please choose an authorized disposal site.
➢
Installation of Your Wine cooler
•
This
appliance is designed to be for free standing installation or built-in (fully recessed)
(Refer to sticker location the back of this appliance). PN7 is only for built in.
•
This appliance is intended to be used exclusively for the storage of wine.
•
Place your Wine cooler on a floor that is strong enough to support it when it is fully loaded.
To level your Wine cooler, adjust the front leveling leg at the bottom of the Wine cooler/
cooler.
•
This appliance is using flammability refrigerant. So never damage the cooling pipework
during the transportation. Locate the Wine cooler away from direct sunlight and sources of
heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat
sources may increase electrical consumption. Extreme cold ambient temperatures may also
cause the unit not to perform properly.
•
Avoid locating the unit in moist areas.
•
Plug the Wine cooler into an exclusive, properly installed-grounded wall outlet. Do not
under any circumstances cut or remove the third (ground) prong from the power cord. Any
questions concerning power and/or grounding should be directed toward a certified
electrician or an authorized Products service center.
•
Door handles, door hinges, trays, and baskets for a minimum period of seven years and
door gaskets for a minimum period of 10 year, after placing the last unit of the model on the
market.
•
Thermostats, temperature sensors, printed circuit boards and light sources are available for
a minimum period of seven years after placing the last unit of the model on the market.
➢
Attention
•
Store wine in sealed bottles.
•
Do not overload the cabinet.
•
Do not open the door unless necessary.
•
Do not cover shelves with aluminum foil or any other shelf material which may prevent air
circulation.
•
Should the Wine cooler be stored without use for long periods it is suggested, after a
careful cleaning, to leave the door ajar to allow air to circulate inside the cabinet in order to
avoid possible formations of condensation, mold, or odors.
Summary of Contents for PN166D
