42 PFAFF
46
Dismantling and re-fitting the take-up lever
46.1
Dismantling
.1
Take out screws 1 (Fig.1)
.2
Loosen screw 2 (caution! Loosen correct screw!).
.3
Pull off bearing plate 3 with crank 4 parallel.
.4
Loosen screws 5 (Fig. 2).
.5
Pull bearing pin 6 (Fig. 3) out, using an M4 screw (from gear cover), pressing lightly against
take-up lever link 7.
.6
Remove cover 8.
.7
Loosen the clamp screws of eccentric pin 9 in arm shaft crank 10 through access window (8).
.8
Set needle bar roughly at bottom dead centre.
.9
Carefully pull out take-up lever 11 together with needle bar crank 12.
46.2
Re-fitting
.1
Place take-up lever 11 together with needle bar crank 12 into arm shaft crank 10 and onto
needle bar stud 13.
.2
Swing up take-up lever link 7, insert bearing pin 6.
Position take-up lever in middle of housing slot, set bearing pin 6 and rear bearing bush
without play against take-up lever link 7 and tighten screw 5 firmly.
.3
Set needle bar at bottom dead centre.
.4
Set eccentric side of eccentric pin 9 towards rear (see arrow at 9).
Observe correct direction!
.5
Replace bearing plate 3 together with crank 4.
Note:
It must be possible to move the bearing plate back and forth easily!
If there is any binding, the take-up lever is jammed, and adjustments 2.3 and 2.4 have
to be repeated.
.6
Tighten screws 1.
.7
Tighten screw 2.
.8
Tighten clamp screws of eccentric pin 9 in arm shaft crank 10 firmly through window 8.
.9
Check that the two screws in the arm shaft crank are really tight.
Summary of Contents for 3822-1/22
