background image

Page 1a

MACHINE SPECIFICATION SHEET

1.

CAUTION:

   In order to ensure correct safety and operation, this machine must be

installed and maintained by an authorised Service Engineer.

2.

CAUTION:

   Should any cover or safety interlock be damaged, the machine must not

be used until service repairs have been completed.

3.

CAUTION:

   This machine must be grounded. Wire colors in the power cord are:

110-120V

220-240V

Connect to:

Green

Green/Yellow

Ground (Earth)

White

Blue

Neutral

Black

Brown

Live (Line)

4.

CAUTION:

   This machine must not be used if the power cord is damaged. It must be

replaced with a similar power cord:

UK

Part no. 141-162-210

EURO

Part no. 141-162-311

US

Part no. 141-162-321

5.

CAUTION:

   For continued protection against risk of fire, replace with the same type

and rating of fuse. The fuse rating and type for this machine is:

   110-120V

       T6.3A 250V

Part no. 141-135-106

   220-240V

       T3.15A 250V

Part no. 141-135-103

6.

Model Details:

   Model name:

Desktop Pressure Sealer

   Model number: 4040/4060

   Input voltage: 110-120V @ 60Hz

220-240V @ 50Hz

   Input current: 3 Amps

1.5 Amps

   Input power:

360 Watts

360 Watts

   Sound output: 75dBa

75dBa

   (measured at 1 meter from the cover and 1.6 meters from the ground)

   Weight:

158lbs (72kg) - unpackaged

Lifting or handling must only be carried out by competent persons using appropriate means.

7.

The use for the machine is pressure sealing documents.

Distributor and Service contact:

Issue 1 Apr 2002

Summary of Contents for AS700



















Reviews: