background image

PFT G 54 E 

 Operating Instructions 

09/2006 

Knauf PFT GmbH & Co.KG  

47 

High pressure pump spare parts list, item number: 00 05 67 92 

 

Pos. Qty  Item 

no. Description 

00 05 67 92  High pressure pump G 54 E 400 V Pk65, crosswise at bottom, cpl. 

00 00 11 30  High pressure pump AV3 PK65N 

20 20 54 00  Reduction nipple, 1" external thread, 1/2" internal thread, no. 241, zinc-plated 

20 20 36 10  Curved section, 1/2" internal/external thread, no. 92, zinc-plated 

20 19 04 10  Hose screw joint, 1/2" external thread, 1/2" socket 

00 05 91 96  Hose clip 19-21 

20 21 36 00  Water/air hose, 1/2" x 1300 mm 

20 42 41 10  Motor connection cable, 0.8 m, CEE plug, 4 x 16 A, 6 h, red, ring eyelet, 4 mm

00 04 11 27  Connector skintop, M20 x 1.5 

10 

20 42 79 00  CEE plug, 4 x 16 A, 6 h, red, no. 252 

11 

20 20 17 00  Geka coupling gasket (pack of 50 pieces) 

12 

20 15 20 00  Water inlet filter Geka coupling 

13 

20 20 09 10  Geka coupling, 3/4" external thread 

14 

20 20 50 00  Reduction nipple, 1" external thread, 3/4" internal thread, no. 241 

15 

20 20 36 20  Curved section, 1" internal/external thread, no. 92, zinc-plated 

16 

20 20 62 00  Nut, M6, DIN 985, zinc-plated 

17 

20 20 93 10  Washer, 6.4 x 18 x 1.5, DIN 9021, zinc-plated 

18 

20 20 71 03  Hex screw, M6 x 20, DIN 933, zinc-plated 

 

Summary of Contents for 00 05 69 13

























































Reviews: