PFT Conveying Pump SWING L Overview – Operation – Spare Parts Lists
Contents
4
14/09/2021
29.1
Check the mortar consistency ........... 29
29.2
Put the SWING L 400V / 230V into
operation ............................................ 30
30
Mortar hoses ............................................... 30
30.1
Prepare mortar hoses ........................ 30
30.2
Connecting the material hose ............ 30
30.3
Switch on the SWING L ..................... 31
31
Establish air supply ................................... 31
31.1
Connect the air hose .......................... 31
32
Spraying gun .............................................. 31
32.1
Connecting the spraying gun ............. 31
32.2
Switch on air compressor 400V
(accessory) ........................................ 32
32.3
Switch on air compressor 230V
(accessory) ........................................ 32
33
Monitor the machine .................................. 32
34
Processing material ................................... 32
34.1
Spraying material ............................... 32
34.2
Speed controller ................................. 33
34.3
Brief interruptions ............................... 34
34.4
For longer work breaks / breaks ........ 34
34.5
Switch off air compressor 400V
(accessory) ........................................ 34
34.6
Switch off air compressor 230V
(accessory) ........................................ 35
35
Remote control ........................................... 35
35.1
Working with the remote control ........ 35
36
Switching off in an emergency ................. 35
37
Measures in case of power cut ................. 36
37.1
Main switch to position “0“ ................. 36
37.2
Relieve mortar pressure .................... 36
37.3
Restart SWING L FU ......................... 37
37.4
Restart SWING L 400V / 230V .......... 37
38
Work on troubleshooting .......................... 38
38.1
Reaction in the event of faults ........... 38
38.2
Fault displays ..................................... 38
38.3
Malfunctions ....................................... 39
38.4
Safety ................................................. 39
38.5
Table of malfunctions .........................40
39
Signs for hose blockages: .........................41
39.1
Indications of clogged hoses: .............41
39.2
Possible causes: ................................41
39.3
Earlier damage to the mortar hose .....41
40
Removal of blockages in the hose ............42
40.1
Change the direction of rotation for
SWING L FU .......................................42
40.2
Change the direction of rotation for
SWING L ............................................43
40.3
Blockage does not dislodge ...............43
40.4
Switch the SWING L FU on again
after removing the blockage ...............44
40.5
Switch the SWING L on again after
removing the blockage .......................44
41
End of work / Cleaning the machine .........44
41.1
Securing against restarting .................44
41.2
Cleaning the SWING L .......................45
41.3
Decouple mortar hose ........................46
41.4
Drain the remaining water ..................46
41.5
Mörtelschlauch reinigen .....................46
42
Clean the pump ...........................................47
42.1
Remove the pump ..............................47
43
Measures in case of risk of frost ...............47
44
Maintenance ................................................48
44.1
Safety .................................................48
44.2
When working on and in the control
box ......................................................48
44.3
Maintenance plan ...............................50
44.4
Air filter compressor ...........................50
44.5
Tightening torque for the screws on
the material container .........................51
44.6
Clean the filter insert for the
frequency converter ............................51
44.7
Change pump .....................................52
44.8
Measures after effected
maintenance .......................................53
44.9 53
45
Periodic inspection .....................................53
