INSTALLATION
DISCLAIMER
-
This product is intended for advanced users. Please
consult with a qualified technician for installation, improper instal-
lation may result in damage to your equipment. While all efforts
have been made to provide the most comprehensive information
possible, Phanteks assumes no liability expressed or implied for
any damage(s) occurring to your components as a result of using
Phanteks cooling products, either due to mistake or omission on
our part in the below instructions, or due to failure or defect in the
Phanteks cooling products.
WARNING -
Turn off the power to your system and discharge your
body’s static electric charge by touching a grounded surface – for
example, the metal surface of the power supply or chassis – before
performing any hardware procedure. Phanteks assumes no liability
for any damage, caused directly or indirectly, by improper installation
of any components. If you do not feel comfortable with performing
the installation procedure, consult a qualified computer technician.
*Please do not disassemble the water block. Warranty will be voided.
STEP 1. REMOVING STOCK COOLER
Take out the top EVA-FOAM from the box to use as a base
for your GPU placement.
Remove all highlighted screws. All heat sink assembly screws should be removed, including
self-adhesive washers on both sides of the PCB (if present).
Phanteks Glacier G1080
M2.5x5, washers
QTY: 20
PACKAGE CONTENTS
Glacier G1080 Water Block
(MSI GTX 1080/1070 GAMING)
QTY: 1
Thermal Pads
QTY: 2
Description:
For applying on circuit board on GPU
PH-GB1080MS_BK01/CR01
INSTALLATION
STEP 1.
REMOVING STOCK COOLER
Remove all highlighted screws. All heat sink assembly screws should be
removed, including self-adhesive washers on both sides of the PCB (if present).
DISCLAIMER
-
This product is intended for advanced users. Please
-
have been made to provide the most comprehensive information
possible, Phanteks assumes no liability expressed or implied for
any damage(s) occurring to your components as a result of using
Phanteks cooling products, either due to mistake or omission on
our part in the below instructions, or due to failure or defect in the
Phanteks cooling products.
WARNING -
body’s static electric charge by touching a grounded surface – for
example, the metal surface of the power supply or chassis – before
performing any hardware procedure. Phanteks assumes no liability
for any damage, caused directly or indirectly, by improper installation
of any components. If you do not feel comfortable with performing
*Please do not disassemble the water block. Warranty will be voided.
MAKE SURE TO UNPLUG THE RGB LED CABLES WHEN YOU REMOVE THE HOUSING.
Thermal Compound (PH-NDC_01)
QTY: 1
Phanteks Plugs
QTY: 2
LIGHTLY COAT NVIDIA GPU CHIP WITH ENCLOSED THERMAL PASTE.
TAKE OUT THE TOP EVA-FOAM LAYER FROM THE BOX TO USE AS BASE FOR YOUR GPU PLACEMENT.
STEP 2.
APPLYING THERMAL COMPOUND
Wipe off the remains of the original thermal compound until components and
Circuit board are completely clean (we recommend using a isopropanol
cleaning pad). Apply a light coat (see image) of the PH-NDC_01 thermal paste.
Phanteks RGB Cable
QTY: 1
INSTALLATION GUIDE
MSI GAMING
M2.5x5, washers
QTY: 20
STEP 2. APPLYING THERMAL COMPOUND
Wipe off the remains of the original thermal compound until components and circuit board are
completely clean (we recommend using a isopropanol cleaning pad). Apply a light coat (see
image) of the PH-NDC-01 thermal paste.
Lightly coat Nvidia GPU Chip with the enclosed thermal paste.
M2.5x5, washers
QTY: 10 (Spare 4pcs)
Washers
QTY: 8 (Spare 4pcs)
Hex Nuts
QTY: 4
PACKAGE CONTENTS
Glacier G1080 Water Block
(Nvidia GTX 1080Ti)
QTY: 1
Thermal Pads
QTY: 3
Description:
For applying on circuit board on GPU
Thermal Compound (PH-NDC_01)
QTY: 1
Phanteks Plugs
QTY: 2
Hex Socket Wrench
QTY: 1
Phanteks RGB Cable for Phanteks case
(Option a)
QTY: 1
Phanteks Glacier G1080
M2.5x5, washers
QTY: 20
PACKAGE CONTENTS
Glacier G1080 Water Block
(MSI GTX 1080/1070 GAMING)
QTY: 1
Thermal Pads
QTY: 3
Description:
For applying on circuit board on GPU
PH-GB1080MS_BK01/CR01
INSTALLATION
STEP 1.
REMOVING STOCK COOLER
Remove all highlighted screws. All heat sink assembly screws should be
removed, including self-adhesive washers on both sides of the PCB (if present).
DISCLAIMER
-
This product is intended for advanced users. Please
-
have been made to provide the most comprehensive information
possible, Phanteks assumes no liability expressed or implied for
any damage(s) occurring to your components as a result of using
Phanteks cooling products, either due to mistake or omission on
our part in the below instructions, or due to failure or defect in the
Phanteks cooling products.
WARNING -
body’s static electric charge by touching a grounded surface – for
example, the metal surface of the power supply or chassis – before
performing any hardware procedure. Phanteks assumes no liability
for any damage, caused directly or indirectly, by improper installation
of any components. If you do not feel comfortable with performing
*Please do not disassemble the water block. Warranty will be voided.
MAKE SURE TO UNPLUG THE FAN AND RGB LED CABLES WHEN YOU REMOVE THE HOUSING.
Thermal Compound (PH-NDC_01)
QTY: 1
Phanteks Plugs
QTY: 2
LIGHTLY COAT NVIDIA GPU CHIP WITH ENCLOSED THERMAL PASTE.
STEP 3.
APPLYING THERMAL COMPOUND
Wipe o the remains of the original thermal compound until components and
Circuit board are completely clean (we recommend using a isopropanol
cleaning pad). Apply a light coat (see image) of the PH-NDC_01 thermal paste.
Phanteks RGB Cable for GPU
QTY: 1
INSTALLATION GUIDE
MSI GAMING
M2.5x5, washers
QTY: 8 (spare 4 pcs.)
M2.5x8
QTY: 15 (spare 4 pcs.)
TAKE OUT THE TOP EVA-FOAM LAYER FROM THE BOX
TO USE AS BASE FOR YOUR GPU PLACEMENT.
Phanteks RGB Cable for Phanteks Case
QTY: 1
13x160x1.5mm (for Vdd MOSFET)
20x120x1.5mm (for memory IC)
10x120x1.5mm (Spare)
TAKE OUT THE TOP EVA-FOAM LAYER FROM THE BOX
TO USE AS BASE FOR YOUR GPU PLACEMENT.
STEP 2.
REMOVING PCBA BRACKET
Unfasten the screws on the PCBA bracket.
Phanteks RGB Adapter for moth-
erboard
QTY: 1
H4 Hex Socket Wrench needed
Unfasten the screws and use the provided H4 hex socket wrench to remove the hexagonal
spacer-screws (blue). After you remove the housing, do not forget to unplug the fan.
Make sure to remove the two screws located on the I/O. Keep the screws aside to use in step
5.
Make sure to keep the hexagonal spacer-screws aside for later use (Step 5).
PH-GB1080Ti_BK01/CR01
GLACIER G1080 Ti
FOUNDERS EDITION GTX
1080 Ti
