background image

IMPORTANT SAFETY INFORMATION

1. Read these instructions.
2. Keep these instructions.
3. Heed all warning.
4. Follow all instructions
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized 
plug has two blades with one wider than the other. A grounding type plug has two blades 
and a third grounding prong.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience 
receptacles, the wide blade or the third prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or 
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus 
combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus 
has been damaged in any way, such as power-supply cold or plug is damaged, liquid has 
been spilled or object have fallen into the apparatus, the apparatus has been exposed to 
rain or moisture, does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to 
rain or moisture while energized without the properly installed protection.
16. When the power plug or an appliance coupler is used as the means of disconnect, the 
disconnect shall remain readily operable.
17. For Networked Standby mode: 1.8W 10min.

Summary of Contents for OS-440











Reviews: