background image

 

 

 

 

 

Copyright @ 2014 Phicomm Europe GmbH – print only for private use! 

 

page 

14

 of 

49

 

 

2. Introduction 
 

The routers of the FIR series are all-in-one router for home and SOHO users to share 

broadband internet connection over a wired or a wireless network. 

The  speed  of  up  to  300  Mbps  (FIR151B  up  to  150  Mbps)  provides  users  with 

extraordinary smooth internet surfing, internet phone calling and online gaming. 

By  adopting external Omni-directional antenna(s), the product  greatly  increases  the 

wireless range and sensitivity, which enables to receive wireless signals in any corner 

of your home or your office. 

 

The routers of the FIR series support the following features: 

 

speed up to 300 Mbps (FIR151B up to 150Mbps) 

 

backward compatible with 802.11b/g products 

 

health  and  power  saving  allows  parents  or  administrators  to  establish  restricted 

access policies for children or staff 

 

WPS button allows easy ON/OFF of the internet connection 

 

bandwidth control allows administrators to control the bandwidth for each PC 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for FIR151B


















































Reviews: