background image

CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.

Choosing a Suitable Location

1.

The suitable ambient temperature for the module/device is 0°C-
40°C

.

2.

Do  NOT  place   the  module/device  direct   under  sunlight,   in  a
humid   place   or   in   any   location   where   they   may   contact
moisture, dirt, dust.

3.

Do   NOT   place   the   module/device   where   exists   combustible
substances or any source of heat, fires, radiators, boiler etc.

Disposal

This marking indicates that this product should not 
be disposed with other household wastes throughout
the EU. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, 
recycle it responsibly to promote the sustainable 
reuse of material resources. To return your used 
device, please use the return and collection systems
or contact the retailer where the product was 
purchased. They can take this product for 
environmentally safe recycling.

Philio Technology Corporation
8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City 
24257, Taiwan(R.O.C)

www.philio-tech.com

FCC Interference Statement

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.

These   limits   are   designed   to   provide   reasonable   protection

against harmful interference in a residential installation.

This   equipment   generates,   uses,   and   can   radiate   radio   fre-

quency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio commu-
nications.

However, there is no guarantee that interference will not occur

in a particular installation.

If this equipment does cause harmful interference to radio or

television   reception,   which   can   be   determined   by   turning   the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for
help.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including

interference that may cause undesired operation.

FCC   Caution:  Any   changes   or   modifications   not   expressly   ap-
proved   by  the   party  responsible   for   compliance   could   void   the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.

7

Summary of Contents for PAD18








Reviews: