background image

the distributor for inspection and maintenance.

7. While the door is closed, you hear the latch bolt
coming out when you press the programming
button to lock the door; however, three shorts
beeps are emitted. Conversely, while the door is
open, no beeps are emitted when locking the latch
bolt.

Cause: (1) The depth of latch bolt hole is insufficient.
(2) The latch bolt is not aimed at the opening of
the strike.
Solution: (1) Please dig the latch bolt hole for the strike
deeper (min. Depth of 2.5 cm).
(2) Please adjust the strike to the appropriate
position.

Specification

Rated Voltage

DC6V; (Battery AA x 4)

Battery type

Alkaline Battery AA (LR6)

Operating Temperature

0°C - 40°C

Location 

In door use 

Frequency Range

868.40MHz & 869.85MHz / EU 

908.4MHz & 916.0MHz / USA 

922-927MHz / JAPAN     

RF Maximum Power (Peak)

+5dBm (Peak)

RF Maximum Power (Average) -10dBm (Average)

Transmission Range

Minimum 40 m in door 100m 
outdoor line of sight

Modulation Type

FSK (Frequency-Shift Keying)

** Specifications are subject to change and improvement without
notice.              

FCC ID: RHHPSA03

 

   

CAUTION
Risk of explosion if battery is replaced by an incorrect type. 
Dispose of used battery according to the instructions.

Choosing a Suitable Location

1. Do not locate the Module facing direct sunlight, humid or dusty 
place.
2. The suitable ambient temperature for the Module is 0°C~40°C.
3. Do not locate the Module where exists combustible substances 
or any source of heat, e.g. fires, radiators, boiler etc.

Disposal

This marking indicates that this product should not 
be disposed with other household wastes throughout
the EU. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, 
recycle it responsibly to promote the sustainable 
reuse of material resources. To return your used 
device, please use the return and collection systems
or contact the retailer where the product was 

13

Summary of Contents for PSA03















Reviews: