background image

purchased. They can take this product for 
environmental safe recycling.

Philio Technology Corporation
8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City 
24257, Taiwan(R.O.C)

w

   ww.philio-tech.com

 

 

 

FCC Interference Statement

This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC 
Rules.
These limits are designed to provide reasonable protection 
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or tele-
vision reception, which
can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one of the fol-
lowing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from 
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for 
help.
This device complies with Part 15 of the FCC Rules. Operation is 
subject
to the following two conditions:
(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including 
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly ap-
proved by the party responsible for compliance could void the 
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.

14

Summary of Contents for PSA03















Reviews: