background image

NO.

Name

Def.

Vali

A

B

C

Description

2 Basic Set 

Level

0xFF

All

  

Setting the BASIC command value 
to turn on the light. The 0xFF(-1) 
means turn on the light. For dimmer
equipment 1 to 100 means the light
strength.
0 means turn off the light.

7

(*)

Customer 

Function

0

All

  

Customer function switch, using bit 
control.

0

  

Bit0

: Switch AV control/Lighting 

group control. (0: AV control, 1: 
lighting group control)

0

Bit1

: Reserve.

0

Bit2

: Reserve.

0

Bit3

: Reserve.

0

Bit4

: Reserve.

0

Bit5

: Reserve.

0

Bit6

: Reserve.

0

Bit7

: Reserve.

10

Auto 

Report 

Battery 

Time

12

0 ~

127

  

The interval time for auto report the
battery level. 0 means turn off auto 
report battery.
Each tick means 30 minutes. The 
default value is 12(6 hours). 

82

Association

Group 2 

Basic Set 

Level

0

All

  

Setting the BASIC command value 
to turn on the light in the 
association group 2. 
0 means using the value of 
configuration 2 to set.

83

Association

Group 3 

Basic Set 

Level

0

All

  

Setting the BASIC command value 
to turn on the light in the 
association group 3. 
0 means using the value of 
configuration 2 to set.

84

Association

Group 4 

Basic Set 

Level

0

All

  

Setting the BASIC command value 
to turn on the light in the 
association group 4. 
0 means using the value of 
configuration 2 to set.

85

Association

Group 5 

Basic Set 

Level

0

All

  

Setting the BASIC command value 
to turn on the light in the 
association group 5. 
0 means using the value of 
configuration 2 to set.

86

Association

Group 6 

Basic Set 

Level

0

All

  

Setting the BASIC command value 
to turn on the light in the 
association group 6. 
0 means using the value of 
configuration 2 to set.

87

Association

Group 7 

Basic Set 

Level

0

All

  

Setting the BASIC command value 
to turn on the light in the 
association group 7. 
0 means using the value of 
configuration 2 to set.

88

Association

Group 8 

Basic Set 

Level

0

All

  

Setting the BASIC command value 
to turn on the light in the 
association group 8. 
0 means using the value of 
configuration 2 to set.

89 Association

Group 9 

0

All

  

Setting the BASIC command value 
to turn on the light in the 

Summary of Contents for PSR03-A









Reviews: