background image

Maintenance

Panel
------ Normally you don't need to clean the panel frequently. It depends on the local environment;
------ If in heavy dust area

It is required to clean the solar module regularly with a damp towel to guarantee 

optimum performance of the solar panel;
------ Do not use any type of solvent for cleaning and be careful not to put too much pressure on the 
         module while cleaning;
------ You Should clean small ads regular;
------ You should trim the trees and branches which cover the PV panel regular;

Battery
------ Battery normally does not need any maintenance within the warranty. If any abnormal symptom or 
special requirement, suggest following test can be taken:  
1. Check whether there is some loose connection;
2. Measure and record ambient temperature in the pole;
3. Check the battery if it has deformation;

Battery Storage
The battery should be stored in clean and dry environment.
Storage time: battery is ex-work in fully charged, storage time should be limited. For ensuring battery 
performance, do not exceed storage time as following definition: 

Under -20

~25

, six months;

Under -20

~35

, three months;

Under -20

~45

, one month;

Warning
------ The recycle of the used battery should strictly follow the local laws and regulations. It is forbidden to 
handle the battery as normal garbage for disposal;
------ Do not open, short circuit, or mutilate batteries as injury may occur;
------ Do not put the battery into a pool;
------ Never move battery by pulling the cables of the battery;
------ The installation is highly suggested during the day. 
------ Only be charged with authorized charger by Philips.
------ Handle the panel pole and battery with great care during the installation and transportation;
------ 

ALWAYS 

keep sparks, flames and smoking materials away from the battery

------ In case of  

FIRE

: To extinguish a fire of a battery, use CO2, foam, or dry chemical extinguishing media. 

Do NOT 

discharge the extinguisher directly onto the battery. The resulting thermal shock may cause cracking 

of the battery case/cover.

Important

If you have ANY question concerning safety when working with the battery system, contact your 
local Philips sales/service representative to clarify any of the noted safety precautions, or, call  the 
corporate office number listed on the back of this manual and ask for professional

 

service.

Maintenance

Summary of Contents for 01800502












Reviews: