Reinstall channels
You can search for and reinstall channels and leave
all other TV settings untouched. Alternatively, you can
do a full new TV installation.
If a child lock code is set, you will need to enter this
code before you can reinstall channels.
Reinstall channels
To reinstall the channels only . . .
1 -
Press
and select
Setup
and press
OK
.
2 -
Select
Search for channels
>
Re-install
channels
and press
OK
.
3 -
Select the country where you install the TV.
4 -
Select
Antenna
(DVB-T)
or
Cable (DVB-C)
. The
channel search may take a few minutes. Follow the
instructions on screen.
Full installation
To redo a full TV installation . . .
1 -
Press
and select
Setup
and press
OK
.
2 -
Select
TV settings
>
General settings
>
Reinstall
TV
and press
OK
. The installation may take a few
minutes. Follow the instructions on screen.
Factory settings
Factory settings sets the TV back to the original TV
settings for picture and sound. To switch back to the
original Factory settings . . .
1 -
Press
and select
Setup
and press
OK
.
2 -
Select
TV settings
>
General settings
>
Factory
settings
and press
OK
.
3 -
Press
OK
to confirm.
4 -
Press
, repeatedly if necessary, to close the
menu.
Channel list copy
Introduction
Channel list copy is intended for dealers and expert
users. In some countries, Channel list copy is only
available for copying satellite channels.
With
Channel list copy
, you can copy the channels
installed on one TV onto another Philips TV of the
same range. With Channel list copy, you avoid the
time-consuming channel search by uploading a
predefined channel list on a TV. Use a USB flash drive
of minimum 1 GB.
Conditions
• Both TVs are from the same year range.
• Both TVs have the same hardware type. Check the
hardware type on the TV type plate on the back of
the TV. Typically noted as Q . . . LA
• Both TVs have compatible software versions.
Current version
You can check the current version of the TV software
with
Current software
info
in
>
Setup
>
Software settings
.
Copy channel list
To copy a channel list . . .
1 -
Switch on the TV which has its channels installed.
Plug in a USB memory device.
2 -
Press
and select
Setup
and press
OK
.
3 -
Select
TV settings
>
General settings
>
Channel
list copy
>
Copy to USB
and press
OK
. To copy the
channel list from this TV, you might be asked to enter
the Child lock code you entered during the
installation.
4 -
When copying is done, unplug the USB memory
device.
Now you can upload the copied channel list onto
another Philips TV.
Upload channel list
Upload a copied channel list
Depending on whether your TV is already installed or
not, you must use a different way to upload a channel
list.
To a TV that is not yet installed
1 -
Plug in the power plug to start the installation and
select language and country. You can skip Search for
channels. Finish the installation.
2 -
Plug in the USB memory device that holds the
channel list of the other TV.
3 -
To start the channel list upload, press
and
select
Setup
and press
OK
.
4 -
Select
TV settings
>
General settings
>
Channel
list copy
>
Copy to TV
and press
OK
. You might be
asked to enter the Child lock code of this TV.
5 -
The TV notifies you if the channel list is copied to
the TV successfully. Unplug the USB memory device.
To an already installed TV
1 -
Verify the country setting of the TV. (To verify this
setting, press
and select
Setup
and press
OK
.
Select
Search for channels
>
Re-install channels
and
press
OK
. Press
and later
Cancel
to leave the
Search for channels.)
If the country is correct continue with step 2.
If the country is not correct, you need to start a
reinstallation. To start the reinstallation, press
and
select
Setup
and press
OK
. Select
TV settings
>
General settings
>
Reinstall TV
>
OK
. Select the
correct country and skip the Search for channels.
Finish the installation. When done, continue with step
2.
2 -
Plug in the USB memory device that holds the
channel list of the other TV.
31
