3 -
To start the channel list upload, press
and
select
Setup
and press
OK
.
4 -
Select
TV settings
>
General settings
>
Channel
list copy
>
Copy to TV
and press
OK
. You might be
asked to enter the Child lock code of this TV.
5 -
The TV notifies you if the channel list is copied to
the TV successfully. Unplug the USB memory device.
DVB-T or DVB-C
DVB-T or DVB-C reception
If both DVB-T and DVB-C reception is available in
your country and if this TV is ready to receive DVB-T
and DVB-C for your country, you have selected one
or the other during the channel installation.
If you want to change the DVB setting to start a new
channel installation . . .
1 -
Press
and select
Setup
and press
OK
.
2 -
Select
Channel settings
and press
OK
.
3 -
Select
Channel installation
>
Antenna connection
>
Antenna (DVB-T)
or
Cable (DVB-C)
and press
OK
.
4 -
Select the DVB setting you want.
5 -
Press
, repeatedly if necessary, to close the
menu.
DVB-C channel installation
For ease of use, all DVB-C settings are set to
automatic.
If your DVB-C provider gave you specific DVB-C
values, the network ID or network frequency, enter
these values when the TV asks for them during
installation.
It might be necessary to adjust the scanning (full or
quick scan) or enter a specific symbol rate in the
Settings
menu while installing. To set a
Symbol rate
,
first set the Symbol rate to
Manual
.
Channel number conflicts
In some countries, different TV channels
(broadcasters) might have the same channel number.
While installing, the TV shows the list with channel
number conflicts. You need to select which TV
channel you want to install on a channel number with
multiple TV channels.
DVB-T + DVB-C
If you can use a DVB-T antenna input but also a DVB-
C input, you can set up your TV for both DVB-T and
DVB-C. Install one system followed by the other with
the necessary settings.
Once each system is installed, you need to switch the
antenna input signal on the
Antenna
connection on
the back of the TV and set the TV in the appropriate
system to view the installed channels on TV.
To select the DVB-T or DVB-C setting, see above.
DVB settings
Access DVB settings
1 -
Press
and select
Setup
and press OK.
2 -
Select
Search for channels
and press OK.
3 -
Select
Re-install Channels
.
4 -
Select the country where you install this TV.
5 -
Select
Cable (DVB-C)
.
6 -
Select
Start to search channels
, or
select
Settings for DVB-C settings
.
7 -
Press
, repeatedly if necessary, to close the
menu.
Symbol rate mode
If your cable provider did not give you a specific
symbol rate
value to install the TV channels, leave the
Symbol rate mode
setting on
Automatic
.
If you received a specific symbol rate value, select
Manual
. However, the value you received could be in
the predefined list of symbol rates already. Select
Predefined symbol rates
to check if your value is
available automatically.
Symbol rate
With the
Symbol rate mode
set to
Manual
, you can
enter the symbol rate value you received from your
cable provider. To enter the value, use the number
keys.
Network frequency mode
If you intend to use the fast
Quick scan
method in
Frequency scan
to search for channels, select
Automatic
. The TV will use 1 of the predefined
network frequencies (or HC - homing channel) as
used by most cable providers in your country.
If you received a specific network frequency value to
search for channels, select
Manual
.
Network frequency
With the
Network frequency mode
set to
Manual
, you
can enter the network frequency value received from
your cable provider here. To enter the value, use the
number keys.
Frequency scan
Select the method of searching for channels. You can
select the faster
Quick scan
method and use the
predefined settings used by most cable providers in
32
