Precautions, Notes, and Abbreviation List
3.
result in sets which have the same CTN (Commercial Type
Number; e.g. 28PW9515/12) but which have a different B.O.M.
number.
By looking at the third digit of the serial number, one can
identify which B.O.M. is used for the TV set he is working with.
If the third digit of the serial number contains the number “1”
(example: AG1B033500001), then the TV set has been
manufactured according to B.O.M. number 1. If the third digit is
a “2” (example: AG2B0335000001), then the set has been
produced according to B.O.M. no. 2. This is important for
ordering the correct spare parts!
For the third digit, the numbers 1...9 and the characters A...Z
can be used, so in total: 9 plus 26= 35 different B.O.M.s can be
indicated by the third digit of the serial number.
Identification: The bottom line of a type plate gives a 14-digit
serial number. Digits 1 and 2 refer to the production centre (e.g.
SN is Lysomice, RJ is Kobierzyce), digit 3 refers to the B.O.M.
code, digit 4 refers to the Service version change code, digits 5
and 6 refer to the production year, and digits 7 and 8 refer to
production week (in example below it is 2010 week 10 / 2010
week 17). The 6 last digits contain the serial number.
Figure 3-1 Serial number (example)
3.3.7
Board Level Repair (BLR) or Component Level Repair
(CLR)
If a board is defective, consult your repair procedure to decide
if the board has to be exchanged or if it should be repaired on
component level.
If your repair procedure says the board should be exchanged
completely, do not solder on the defective board. Otherwise, it
cannot be returned to the O.E.M. supplier for back charging!
3.3.8
Practical Service Precautions
•
It makes sense to avoid exposure to electrical shock.
While some sources are expected to have a possible
dangerous impact, others of quite high potential are of
limited current and are sometimes held in less regard.
•
Always respect voltages. While some may not be
dangerous in themselves, they can cause unexpected
reactions that are best avoided. Before reaching into a
powered TV set, it is best to test the high voltage insulation.
It is easy to do, and is a good service precaution.
3.4
Abbreviation List
0/6/12
SCART switch control signal on A/V
board. 0 = loop through (AUX to TV),
6 = play 16 : 9 format, 12 = play 4 : 3
format
AARA
Automatic Aspect Ratio Adaptation:
algorithm that adapts aspect ratio to
remove horizontal black bars; keeps
the original aspect ratio
ACI
Automatic Channel Installation:
algorithm that installs TV channels
directly from a cable network by
means of a predefined TXT page
ADC
Analogue to Digital Converter
AFC
Automatic Frequency Control: control
signal used to tune to the correct
frequency
AGC
Automatic Gain Control: algorithm that
controls the video input of the feature
box
AM
Amplitude Modulation
AP
Asia Pacific
AR
Aspect Ratio: 4 by 3 or 16 by 9
ASF
Auto Screen Fit: algorithm that adapts
aspect ratio to remove horizontal black
bars without discarding video
information
ATSC
Advanced Television Systems
Committee, the digital TV standard in
the USA
ATV
See Auto TV
Auto TV
A hardware and software control
system that measures picture content,
and adapts image parameters in a
dynamic way
AV
External Audio Video
AVC
Audio Video Controller
AVIP
Audio Video Input Processor
B/G
Monochrome TV system. Sound
carrier distance is 5.5 MHz
BDS
Business Display Solutions (iTV)
BLR
Board-Level Repair
BTSC
Broadcast Television Standard
Committee. Multiplex FM stereo sound
system, originating from the USA and
used e.g. in LATAM and AP-NTSC
countries
B-TXT
Blue TeleteXT
C
Centre channel (audio)
CEC
Consumer Electronics Control bus:
remote control bus on HDMI
connections
CL
Constant Level: audio output to
connect with an external amplifier
CLR
Component Level Repair
ComPair
Computer aided rePair
CP
Connected Planet / Copy Protection
CSM
Customer Service Mode
CTI
Color Transient Improvement:
manipulates steepness of chroma
transients
CVBS
Composite Video Blanking and
Synchronization
DAC
Digital to Analogue Converter
DBE
Dynamic Bass Enhancement: extra
low frequency amplification
DCM
Data Communication Module. Also
referred to as System Card or
Smartcard (for iTV).
DDC
See “E-DDC”
D/K
Monochrome TV system. Sound
carrier distance is 6.5 MHz
DFI
Dynamic Frame Insertion
DFU
Directions For Use: owner's manual
DMR
Digital Media Reader: card reader
DMSD
Digital Multi Standard Decoding
DNM
Digital Natural Motion
10000_053_110228.eps
110228
