In certain countries, the automatic channel update is
done while watching TV or on any moment when the
TV is in Standby.
Manual Channel Update
You can always start an channel update yourself.
To start a channel update manually…
1 -
Press
, select
All Settings
and press
OK
.
2 -
Select
Channels
>
Satellite Installation
and
press
OK
.
3 -
Select
Search for Channels
and press
OK
.
4 -
Select
Update Channels
and press
OK
. The TV
will start updating. The update may take a few
minutes.
5 -
Follow the instructions on screen. The update
may take a few minutes.
6 -
Select
Finish
and press
OK.
Add a Satellite
You can add an additional satellite to your current
satellite installation. The installed satellites and their
channels remain untouched. Some satellite operators
do not allow adding a satellite.
The additional satellite should be seen as an extra, it
is not your main satellite subscription or not the main
satellite of which you use its channel package.
Typically, you would add a 4th satellite when you
have 3 satellites already installed. If you have 4
satellites installed, you might consider removing one
first to be able to add a new satellite.
Setup
If you currently have only 1 or 2 satellites installed, the
current installation settings might not allow adding an
extra satellite. If you need to change the installation
settings, you must redo the complete satellite
installation. You cannot use
Add satellite
if a change
of settings is needed.
To add a satellite…
1 -
Press
, select
All Settings
and press
OK
.
2 -
Select
Channels
>
Satellite Installation
and
press
OK
.
3 -
Select
Search for satellite
and press
OK
.
4 -
Select
Add Satellite
and press
OK
. The current
satellites are shown.
5 -
Select
Search
and press
OK
. The TV will
search for new satellites.
6 -
If the TV has found one or more satellites,
select
Install
and press
OK
. The TV installs the
channels of the found satellites.
7 -
Select
Finish
and press
OK
to store the
channels and radio stations.
Remove a Satellite
You can remove one or more satellites from your
current satellite installation. You remove the satellite
and its channels. Some satellite operators do not
allow removing a satellite.
To remove satellites…
1 -
Press
, select
All Settings
and press
OK
.
2 -
Select
Channels
>
Satellite Installation
and
press
OK
.
3 -
Select
Search for satellite
and press
OK
.
4 -
Select
Remove Satellite
and press
OK
. The
current satellites are shown.
5 -
Select a satellite and press
OK
to mark or
unmark them to remove.
6 -
Press
(left) repeatedly if necessary, to close
the menu.
Manual Installation
Manual Installation is intended for expert users.
You can use Manual Installation to quickly add new
channels from a satellite transponder. You need to
know the frequency and polarization of the
transponder. The TV will install all channels of that
transponder. If the transponder was installed before,
all its channels - the former and the new ones - are
moved to the end of the channel list All.
You cannot use Manual installation if you need to
change the number of satellites. If this is needed, you
have to do a complete installation with Install
Satellites.
To install a transponder…
1 -
Press
, select
All Settings
and press
OK
.
2 -
Select
Channels
>
Satellite Installation
and
press
OK
.
3 -
Select
Manual Installation
and press
(right)
to enter the menu.
4 -
If you have more than 1 satellite installed, select
LNB
for which you want to add channels.
5 -
Set the
Polarisation
you need. If you set
the
Symbol Rate Mode
to
Manual
, you can enter
the symbol rate in
Symbol Rate
manually.
6 -
Press the arrows
(up) or
(down) to adjust
the frequency, and select
Done
.
7 -
Select
Search
and press
OK
. The signal
strenght is shown on screen.
8 -
If you want to store the channels of a new
transponder, select
Store
and press
OK
.
9 -
Press
(left) repeatedly if necessary, to close
the menu.
94
