satellite tuners. A satellite tuner cannot have the same
user band number as another satellite tuner in the
Unicable system.
User band frequency
Next to the unique user band number, the built-in
satellite receiver needs the frequency of the selected
user band number. These frequencies are mostly
shown next to the user band number on a Unicable
switchbox.
Add a satellite
You can add an additional satellite to your current
satellite installation. The installed satellites and their
channels remain untouched. Some satellite operators
do not allow adding a satellite.
The additional satellite should be seen as an extra, it
is not your main satellite subscription or not the main
satellite of which you use its channel package.
Typically, you would add a 4th satellite when you
have 3 satellites already installed. If you have 4
satellites installed, you might consider removing one
first to be able to add a new satellite.
Setup
If you currently have only 1 or 2 satellites installed, the
current installation settings might not allow adding an
extra satellite. If you need to change the installation
settings, you must redo the complete satellite
installation. You cannot use
Add satellite
if a change
of settings is needed.
To add a satellite…
1 -
Press
, select
Satellite installation
and
press
OK
.
2 -
Select
Search for satellite
and press
OK
.
3 -
Select
Add Satellite
and press
OK
. The current
satellites are shown.
4 -
Select
Add
and press
OK
. The TV will search for
new satellites.
5 -
If the TV has found one or more satellites,
select
Install
and press
OK
. The TV installs the
channels of the found satellites.
6 -
To store the channels and radio stations,
select
Finish
and press
OK
.
Remove a satellite
You can remove one or more satellites from your
current satellite installation. You remove the satellite
and its channels. Some satellite operators do not
allow removing a satellite.
To remove satellites…
1 -
Press
, select
Satellite installation
and
press
OK
.
2 -
Select
Search for satellite
and press
OK
.
3 -
Select
Remove Satellite
and press
OK
. The
current satellites are shown.
4 -
Use the arrows keys to select the satellite you
want to remove.
5 -
Press
OK
to mark a satellite to remove.
Press
OK
again to unmark.
6 -
Select
Remove
, press
OK
and confirm. The
satellites are removed.
7 -
Select
Exit
and press
OK
to close Remove
satellite.
Manual installation
Manual Installation is intended for expert users.
You can use Manual Installation to quickly add new
channels from a satellite transponder. You need to
know the frequency and polarization of the
transponder. The TV will install all channels of that
transponder. If the transponder was installed before,
all its channels - the former and the new ones - are
moved to the end of the channel list All.
You cannot use Manual installation if you need to
change the number of satellites. If this is needed, you
have to do a complete installation with Install
Satellites.
To install a transponder…
1 -
Press
, select
Satellite installation
and
press
OK.
2 -
Select
Manual Installation
and press
(right)
to enter the menu.
3 -
If you have more than 1 satellite installed, select
LNB
for which you want to add channels.
4 -
Set the
Polarisation
you need. If you set
the
Symbol Rate Mode
to
Manual
, you can enter
the symbol rate in
Symbol Rate
manually.
5 -
Press the arrows
(up) or
(down) to adjust
the frequency, and select
Done
.
6 -
Select
Search
and press
OK
. The signal
strenght is shown on screen.
7 -
If you want to store the channels of a new
transponder, select
Store
and press
OK
.
8 -
Press
(left) repeatedly if necessary, to close
the menu.
Reorder and rename channels
You can reorder and rename satellite channels.
Reorder
You can only reorder channels in the Favourites list.
For more information on Reordering satellite
channels, press
Keywords
and look up
Satellite,
reorder channels
.
69
