1 Notice
Trademarks are the property of Koninklijke Philips N.V. or
their respective owners.
Funai Corporation reserves the right to change products at
any time without being obliged to adjust earlier supplies
accordingly.
The material in this Owner’s Manual is believed adequate for
the intended use of the system. If the product or its individual
modules or procedures are used for purposes other than
those specified herein, confirmation of their validity and
suitability must be obtained. Funai Corporation warrants that
the material itself does not infringe any United States patents.
No further warranty is expressed or implied.
Funai Corporation cannot be held responsible neither for any
errors in the content of this document nor for any problems
as a result of the content in this document. Errors reported to
Funai Corporation will be adapted and published on the
Funai Corporation support website as soon as possible.
Pixel characteristics
This LCD product has a high number of color pixels.
Although it has effective pixels of 99.999% or more, black
dots or bright points of light (red, green or blue) may
appear constantly on the screen. This is a structural
property of the display (within common industry standards)
and is not a malfunction.
Warranty
No components are user serviceable. Do not open or
remove covers to the inside of the product. Repairs may
only be done by Service Centers and official repair shops.
Failure to do so shall void any warranty, stated or implied.
Any operation expressly prohibited in this manual, any
adjustments or assembly procedures not recommended or
authorized in this manual shall void the warranty.
Federal Communications Commission Notice
This equipment has been tested and found to comply with
the limits for a Class B Digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
the receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio or
television technician for help.
Declaration of conformity
Trade name
: PHILIPS
Responsible party
: Funai Corporation, Inc.
Model
: 75PFL6601, 65PFL6601/F7, 65PFL6601/F7 A
Address
: 12489 Lakeland Road, Santa Fe Springs, CA
90670, USA*
Telephone number
: 1 866 202 5960
*
This is not the mailing address for Open Source Software or Customer
service.
Modifications
This apparatus may generate or use radio frequency energy.
Changes or Modifications to this apparatus may cause
harmful interference.
Any Modifications to the apparatus must be Approved by
Funai Corporation.
The user could lose the authority to operate this apparatus if
an unauthorized Change or Modification is made.
Cables
Connections to this device must be made with shielded
cables with metallic RFI / EMI connector hoods to maintain
compliance with FCC Rules and Regulations.
Canadian notice
CAN ICES-3 (B)/NMB-3 (B)
Standard Television Receiving Apparatus, Canada BETS-7
/ NTMR-7.
The following FCC/IC RSS applies to the
Wireless LAN adapter included in this product.
FCC Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Country Code Statement
For product available in the USA market, only channel
1
∼
1 1 can be operated. Selection of other channels is not
possible.
To maintain compliance with FCC RF exposure
requirements, use only belt-clips, holsters or similar
accessories that do not contain metallic components in
its assembly. The use of accessories that do not satisfy
these requirements may not comply with FCC RF
exposure requirements and should be avoided.
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not
cause interference and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
5150-5250 MHz band is restricted to indoor
operations only.
High-power radars are allocated as primary users (i.e.
priority users) of the bands 5250-5350 MHz and
5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.
Compliance with IC requirement RSS-210 A9.4.4
Data transmission is always initiated by software,
which is the passed down through the MAC, through
the digital and analog baseband, and finally to the RF
chip. Several special packets are initiated by the MAC.
These are the only ways the digital baseband portion
will turn on the RF transmitter, which it then turns off at
the end of the packet. Therefore, the transmitter will be
on only while one of the aforementioned packets is
being transmitted. In other words, this device
automatically discontinue transmission in case of
either absence of information to transmit or
operational failure.
5
.
English
65PFL6601 serial numbers beginning with DS4A1702 or lower numbers / 75PFL6601 serial numbers beginning with GZ1
