3 - 2
ACCESSORIES
1 x AC mains lead
1 x Remote Control
TOP
AND
FRONT P
ANEL (See
1
)
1
PROGRAM
CD:
-
programs tracks and reviews the program;
Tuner:
-
programs preset radio stations.
2
CD•FM•MW•L
W
- selects
CD / FM /
MW
/ L
W
function
3
IR SENSOR -
infrared for remote control
4
TUNER
PRESET
4
,
3
- selects a preset radio
station.
5
OPEN•CLOSE
- opens / closes CD door
.
6
Telescopic antenna
- improves FM reception.
7
VOLUME
+
,
-
- to adjust volume level.
8
DBB
(Dynamic Bass Boost)
- activates a more vivid
bass response.
9
2;
- starts or pauses CD playback.
9
- to stop playback or erase a CD program.
SEARCH
,
§§
§
CD
:
- searches
backward
and
forward
within
a
track;
- skips to the beginning of a current track/
previous/ later track.
Tuner: -
(down, up) tunes to radio stations.
0
POWER
- power on / off switch
!
MODE
- selects different play modes: e.g.
REPEA
T
or
SHUFFLE
(random) order
.
@
Display
- shows the status of the set.
BACK P
ANEL (See
1
)
#
AC MAINS
- inlet for mains lead.
$
Battery compartment
- for 6 batteries, type
R-14
,
UM2
or
C-cells
.
REMOTE CONTROL (See
A
)
1
CD
– selects CD sound source
2
y
–
switches the set to standby / on if set
operating on AC power
. (Switches set off only if
battery powered)
3
VOLUME
+
,
-
– adjusts volume level
(up, down)
4
SHUFFLE
– plays all CD tracks in random order
5
BASS
– selects DBB on/off
6
2;
– starts/ pauses CD playback
7
SEARCH
5
,
6
– searches backwards/ forwards
within a track
8
BAND
– selects FM/MW/L
W
waveband
9
PRESET
3
,
4
– selects a preset radio station
(up, down)
0
TUNING
,
§
– tunes to tuner stations
(down, up)
!
TUNER
– selects tuner sound source
@
9
– stops CD playback;
– erases a CD programme
#
¡
,
™
– skips to the beginning of a current track
previous/ subsequent track
$
MUTE
– interrupts/ resumes sound
%
REPEA
T
– repeats a track /programme/ entire CD
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
POWER SUPPL
Y
Whenever convenient, use the AC power supply to
conserve battery life. Make sure you remove the
power plug from the set and wall socket before
inserting batteries.
Batteries (not included)
•
Insert 6 batteries, type
R-14
,
UM-2
or
C-cells
,
(preferably alkaline) with the correct polarity
. (
See
6
)
•
Remote control
Insert 2 batteries, type
AAA
,
R03
or
UM4
(preferably alkaline). (
See
8
)
IMPORT
ANT
!
•I
ncorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or cause
the batteries to burst.
•
Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
•W
hen inserting new batteries, do not try to mix old
batteries with the new ones.
•
Batteries contain chemical substances, so
they should be disposed of properly
.
Using AC Power
1.
Check if the AC power supply
, as shown on the
type plate located on the bottom of the set
,
corresponds to your local power supply
. If it does
not, consult your dealer or service centre.
2.
Connect the mains lead to the wall socket.
3.
To
disconnect the mains supply
, unplug the set
from the wall socket.
Storing your remote control
This set has a special built-in storage compartment for
your remote control. The storage compartment has a
latch to keep your remote control in place, and is
located inside the CD
compartment.
(See
B
)
Placing your set
To
avoid possible staining of
surfaces, please do not stand
this set in vertical position
over a long period.
The type plate is located on the bottom of the
set.
This set complies with the radio interference
requirements of the European Community
.
For users in the U.K., please follow the boxed
instructions ‘Important notes...’ on this sheet.
BASIC FUNCTIONS
Switching on and off and selecting function
1.
Press
POWER
on the set (or
y
on remote
control) to switch on.
2.
Press
CD•FM•MW•L
W
once or more to select :
CD / T
uner
function, and operate the respective
function controls.
3.
Press
POWER
to switch off the set.
Note :
The DBB setting, tuner presets and the
volume level (maximum to 20) will be retained in the
set's memory
.
Adjusting volume and sound (See
2
)
1.
Adjust the volume with the
VOLUME
+
,
-
controls.
™
Display shows the volume level in number from
0-32.
2.
Press
DBB
once or more to select dynamic bass
boost on or off.
™
Display: shows
when activated.
English
CONTROL
POWER
SUPPL
Y
BASIC FUNCTIONS
CONNECTIONS AND CONTROLS
