Move the disk back and forth gently over the skin you want to
treat. Do not push too hard. When you push too hard, the disk
might stop rotating.
Overheat protection
Note: To avoid overheating of the product, do not press the
product too hard onto your skin. The product works best when
you move it over your skin without exerting any pressure.
1 If the overheat protection is activated, the product turns off
automatically. The speed lights start blinking.
2 Let the product cool down.
- The lights stop blinking after 4 seconds.
3 When the product has cooled down, you can turn it on again.
If the lights start to blink again, the product has not yet cooled
down completely
Cleaning
IMPORTANT
- Always switch the product OFF and remove plug from
electrical outlet and product before cleaning.
- Do not use compressed air, scouring pads, abrasive cleaners
or aggressive liquids such as gasoline or acetone to clean the
product.
- Keep the power plug dry.
Cleaning the epilating head
- It is essential for hygienic reasons and optimum performance
that the epilating head, attachments and rotating disks are
cleaned after each use.
- It is strongly recommended to always rinse the epilator head
with cold water to help prevent bacterial growth.
- Never clean, remove, or replace epilating head or attachments
while motor is ON. The rotating disks are not removable from
the epilating head.
- Do not apply pressure or touch rotating disks with hard
objects as this may dent or damage the disks. If damage
occurs, discontinue use immediately.
1. Be certain the product is OFF.
2. Pull the epilating head off the product (Fig. 7).
3. Remove loose hairs from the epilating disks and attachment
with the brush.
Note: Never try to detach the epilating disks from the product.
4. Rinse the epilating head thoroughly under warm tap water.
5. Attach the epilating head to the handle, turn the product ON
and rinse the epilating head under cold tap water for 15 seconds
(Fig. 11).
6. Pull the epilating head off the product, shake off excess water
and dry epilating head and attachments completely with a soft
towel or allow to air dry thoroughly.
7. Place the epilating head back onto the product and push it
against the direction of the arrows until it snaps into place (Fig. 6).
The epilating head only fits onto the product in one direction.
Cleaning the callus removal head
- Clean the callus removal disk with the cleaning brush supplied
(Fig. 19). Remove the disk and clean the inside and outside of
the head with the cleaning brush (Fig. 20).
- If you prefer, you can rinse the callus removal disk and the
inside of the callus removal head under a running tap (Fig. 21).
You can clean the product with a moist cloth (Fig. 22).
Tip: You can also clean the callus removal disk and the inside of
the callus removal head with disinfectant now and then.
Storage
- If you travel, disconnect the callus removal head from the
product. This protects the abrasive disk and also prevents the
immediate surroundings from being damaged by the abrasive
disk. Put protection cap on the head to prevent damage to the
head when you store them.
- Be sure product is turned OFF. Remove cord from outlet and
product before storing in a safe, dry location where it will not
be crushed, banged, or subject to damage.
- Do not wrap cord around product when storing.
- Store cord in a safe location where it will not be cut or
damaged.
- Do not place or store product where it can fall or be pulled
into a tub or sink, water or other liquid while plugged in.
- Put the protective cap on the attachment after use.
Accessories
Replacement parts and accessories may be purchased at a store
near you or on our website
www.philips.com/
store.
Replacement
Replace the callus removal disk when its effectiveness decreases.
We advise you to replace the disk at least once every year
(BCR372).
To buy accessories or spare parts, visit
www.philips.com/parts-
and-accessories
or go to your Philips dealer. You can also
contact the Philips Consumer Care Center in your country (see
the international warranty leaflet for contact details).
This product has no other user-serviceable parts. For assistance
call 1-800-243-7884.
Assistance
For assistance, visit our website:
www.philips.com/support
or
call toll free 1-800-243-7884 (in US only) or 1-866-800-9311 (in
Canada only).
Online information is available 24 hours a day, 7 days a week.
Disposal
- This product contains a rechargeable lithium-ion battery which
must be disposed of properly (Fig. 23).
- Contact your local town or city officials for battery disposal
information. You can also call 1-800-822-8837 or visit
www.call2recycle.org
for battery drop-off locations. In
Canada, call 888-224-9764 or visit
www.call2recycle.ca
for
battery drop-off locations.
- For assistance, visit our website
www.philips.com/support
or
1-800-243-7884 (in US only) or 1-866-800-9311 (in Canada
only).
- Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
For recycling information, please contact your local waste
management facilities or visit
www.recycle.philips.com
Full Two-Year Warranty
Philips North America LLC (USA) and Philips Electronics Ltd
(Canada) warrant this new product against defects in materials or
workmanship for a period of two years from the date of purchase,
and agrees to repair or replace any defective product without
charge.
IMPORTANT
: This warranty does not cover damage resulting
from accident, misuse or abuse, lack of reasonable care, the
affixing of any attachment not provided with the product or loss
of parts or subjecting the product to any but the specified voltage
or batteries.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to
www.philips.com/support
for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not
covered by this warranty. NOTE: No other warranty, written or
oral, is authorized by Philips North America LLC. This warranty
