Circuit-, IC Descriptions and List of Abbreviations
EN 203
DVDR880-890 /0X1
9.
Pin #
Name
Description
125-131
ADDR
10-0
SDRAM Address bus. This signal bus is used to address the external SDRAM(s) used for
133-136
field memories. It should be connected to the A
10-0
bus of the memory chip(s). Please refer
to the Applications section of this data sheet for further details.
176-169
DATA
29-0
SDRAM Data bus. This signal bus is used to transfer the data to and from the external
166-160
SDRAM(s) used for field memories. It should be connected to the DQ
29-0
bus of the memory
157-153
chip when using a 64 Mbit SDRAM. When using two 16 Mbit SDRAMs this 30-bit bus may
150-146
be connected to the two 16-bit data busses of the memories in two ways: either connect 16
143-139
lines to one chip and 14 to the other, or connect 15 to both. In all cases the two unused data
lines on the memory chip(s) should be connected to ground via 22 k resistors. Please refer
to the Applications section of this data sheet for further details.
118
MEMCLKO
SDRAM clock and 2x output sampling clock. This clock is derived from PIXCLK and will be at
double the frequency of YCLKO. This active signal should be connected to the CLK pin(s) on
the SDRAM(s). When the 10-bit output mode selected the output signals will also change at
this clock rate and this should then be used as the output clock..
119
WEN
SDRAM Write Enable. This active low signal should be connected to the WE pin(s) on the
SDRAM(s).
120
RASN
SDRAM Row Address Select. This active low signal should be connected to the RAS pin(s)
on the SDRAM(s).
121
CASN
SDRAM Column Address Select. This active low signal should be connected to the CAS
pin(s) on the SDRAM(s).
122
BSEL
SDRAM Bank Select. When using two 16 Mbit SDRAMs this signal should be connected to
the BA (also called BS or A
11
) pin on both SDRAMs. When using a 64 Mbit SDRAM this
signal should be connected to the BA0 (also called BS0 or A
11
) pin on the SDRAM and BA1/
BS1 (also called BA when BA0 is referred to as A
11
) should be tied low.
41, 50,
TEST
4-0
These pins are used for test purposes only and should always be tied low for normal operation.
51, 109,
111
112, 113 TESTO
1-0
These pins are test outputs and should be left unconnected in normal operation.
Summary of Contents for DVDR880/001
