background image

2

3

 ① Outside Escutcheon 

with Silicone Pad

⑤ Mounting Plate

⑨ Certificate of 

Conformity

 

 Installation kit

② Inside 

Escutcheon with 

Silicone Pad

⑥ User Manual

 Key Tag X 2

 Cleaning Pad

③ Drilling Template

⑦ QSG

 Mechanical 

Key X 2

④ Mortise

⑧ Warranty Card

 Batteries

Strike

Easy

Key

User Manual

Quick Start 

Guide

Easy

Key

Easy

Key

Warranty 

Card

Easy

Key

合格证

Gateway

1  Important information

Safety

Before using Philips EasyKey, please 

read and understand all instructions. 

Damage caused by non-compliance with 

the instructions will not be covered by 

warranty.

Use only the manufacturer-specified 

accessories/components.

Use only the alkaline batteries the 

product is equipped with, or use the 

same specification type of alkaline 

batteries.

Do not forcibly disassemble this product 

to avoid triggering an alarm or damaging 

the product.

Do not scrape the fingerprint sensor 

with sharp objects, otherwise it may cause 

permanent damage.

Do not expose products to environments 

where there is water leakage or splashing.

Do not expose the product to corrosive 

substances to prevent  damaging the 

protective cover.

Do not hang objects on the handle, in 

case it might affect the normal use of the 

lock.

Pleae clean the product with a soft cloth.

Do not remove the battery during 

setting up and operating.

Please let a professional technician 

to install the door lock and follow the 

installation guidelines provided.Do not 

disassemble the lock by yourself. Keep the 

relevant sealed stickers properly. Do not 

easily disclose the password information.

Please modify the default master PIN 

code immediately after finishing installing 

and debugging, and keep the mechanical 

key properly.

Please replace all the batteries 

immediately if there is a low battery alarm. 

Please make sure to correctly match the 

poles (+/-) when installing the batteries.

Caution

Do not place the battery near fire 

sources to avoid explosion. 

Do not use any emergency power 

supply that does not meet the safety 

requirements to power up the product.

Do not connect the 2 poles of the 

batteries with metals to avoid short circuit 

which may lead to an explosion.

Please make sure any component 

replacement is executed by Philips, Philips 

authorized service center or professional 

technicians.

Do not use accessories or parts that have 

been produced by other manufacturers or 

have not been specifically recommended 

by Philips. The use of such accessories and 

parts may void your warranty.

Disposal of used products and 

batteries

You can have your locks reclaimed at 

Philips authorized service centers. You will 

receive corresponding compensation if 

your products meet our conditions.

 

Please familiarize yourself with the local 

electronic product collection system.

Please follow local regulations and do 

not discard used products into ordinary 

household waste.

Proper disposal of used products can 

help to avoid potential negative impacts 

on the environment and human health.

 

Batteries must not be disposed of with 

ordinary household waste.

Please familiarize yourself with the local 

regulations on batteries classification 

recycling. Disposing of batteries properly 

can help avoid a negative impact on the 

environment and human health.

2  Easykey Installation

Packing List

This packing list is for reference only. Please refer to the actual packing items.

Summary of Contents for EasyKey 9000 Series
















Reviews: