Dir
e
c
tio
ns fo
r Use
EN 21
EM6
3.
29
Connect audio receiver
Although your TV is already equipped with a Digital MultiChannel decoder you might want to connect
your own MultiChannel surround receiver.
MultiChannel surround receiver with or without digital input connectors
&
Connect a MultiChannel surround receiver to the
AUDIO OUT
R
and
L
connectors at the back of your TV.
é
If you want the loudspeakers of your TV to act as centre
speaker, also connect an audiocable to the MultiChannel
surround receiver
CENTRE OUT
connector and to the
CENTRE IN
connector at the back of your TV.
“
Select
Centre input On
in the Source menu; See p. 11.The
loudspeakers of the TV will now only produce centre sound.
‘
If necessary, adjust the volume level of the centre sound in the
Centre in volume
menu item of the Source menu.The overall
volume has to be controlled via the MultiChannel surround
receiver.
(
In case of a Digital MultiChannel surround receiver, also connect
the receiver to the
DIGITAL AUDIO OUT
connector.
In this case the loudspeakers of your TV can not act as centre
speaker. Select
Centre input Off
in the Source menu, see p. 11. Also
see the instructions manual of your Digital MultiChannel surround
receiver.
See the separate supplied Cinema Link instruction manual
Attention: the sound info on screen will not correspond with the actual sound reproduction.
Press the
v
key on the remote control repeatedly to select
EXT1
,
EXT2
,
EXT3
,
EXT4
or
SIDE
according to where you connected your equipment at the back or the right side of your TV.
Remark : Most equipment (decoder, recorder) carries out the switching itself, when it is switched on.
To select connected equipment
Cinema Link Surround receiver
Recorder or DVD with EasyLink
The recorder (VCR or DVD+ RW) or DVD can be
operated with the remote control via the Recorder
or DVD menu on screen.
&
Press the
MENU
key on the remote control.
é
Select the
Recorder
or
DVD
menu with the
cursor up/down.
“
Press the cursor left/right, up/down to select
one of the recorder or DVD functions.
The key
®
for recording can be operated in the TV
mode.
If your EasyLink recorder has the system standby
function, when you press the
B
key for 3 seconds,
both TV and the recorder are switched to standby.
Ò
p
‡
π † ®
Ï
Rwd
Play Stop Play
Ffw Rec Eject
Recorder
Ò
p
‡
π †
Ï
Prev. Play
Stop
Play
Next
Eject
DVD
CENTRE IN
CENTRE IN
CENTRE IN
AUDIO
OUT
DIGITAL
AUDIO
OUT
AUDIO
OUT
Wired rear loudspeakers
When no wireless RF surround sound is possible or when there
is too much interference you can still enjoy Dolby Pro Logic II
and Dolby Digital surround sound by connecting the wireless
receiver box to the TV with a stereo cinch to stereo 3.5 mm
jack cable.
&
Connect the (not supplied) cable to the
AUDIO IN (TV)
connector
4
at the wireless receiver box and the
R
and
L
surround outputs at the back of the TV.
é
Select
Off
in the Wireless surround menu item of the Setup,
Speakers menu, p. 9.
28
Side connections
Camera or Camcorder
&
Connect your camera or camcorder as shown.
é
Connect to
VIDEO
2
and
AUDIO L
3
for mono
equipment. For stereo equipment also connect
AUDIO R
3
.
S-VHS quality with an S-VHS camcorder is obtained by
connecting the S-VHS cables with the S-video input
1
and
audio inputs
3
.
Do not connect cable
1
and
2
at the same time. This may cause
picture distortion !
Headphone
&
Insert the plug into the headphone socket
L
as shown.
é
Press
¬
on the remote control to switch off the internal
loudspeakers of the TV.
The headphone impedance must be between 8 and 4000 Ohm. The
headphone socket has a 3.5 mm jack.
In the Sound menu select
Headphone volume
to adjust the
headphone volume.
Note:
When Dual screen/PIP is activated (see p. 16):
- if the main screen displays a TV channel picture, you hear the sound
from the Dual screen/PIP picture through your headphone.
AUDIO
VIDEO
S•VIDEO
1
2
3
®
AUDIO in
AUDIO in
(TV)
(TV)
2.
2.8V RMS
8V RMS
AUDIO in
(TV)
2.8V RMS
13 V DC in
V DC in
13 V DC in
L
R
4 /15W
4 /15W
L
R
4 /15W
1
2
2
1
2
3
4
1
2
3
4
3
3
4
4
SURROUND
Connect extra subwoofer
To enhance the sound reproduction of your TV you can connect
an externally powered subwoofer (between 20 and 250 Hz).
&
Connect the audio cable of the external subwoofer to the
SUBW.
socket at the back of your TV.
é
Select
External
in the Setup, Speakers menu, Subwoofer, p. 9.
For details, please refer to the subwoofer’s manual.
SUBW.
