Dir
e
c
tio
ns fo
r Use
EN 11
EM6
3.
9
TV Setup
The Setup menu contains items that control the
settings of the TV’s functions, features, services and
peripherals you may have connected.
The
Speakers
menu reflects the speaker-related
controls.
The
General
menu allows you to change settings
that will typically be accessed only occasionally.
The
Source
menu allows you to select a source.
The
Decoder
menu allows you to define one or
more programme numbers as decoder programme
numbers.
Speakers General Source Decoder
Test tone
Balance
Centre volume
Surround L volume
Surround R volume
Wireless surround
To front
To surround
Subwoofer
Auto surround
Setup
Your TV is equipped with integrated front left, right
and centre loudspeakers, capable of reproducing
Stereo and Dolby 3 stereo modes.
For Hall, full Dolby Pro Logic II and Dolby Digital
surround sound you should use the two amplified
rear surround speakers.
Depending on the output and Surround mode (see
Main menu,TV, Sound, Surround mode, p. 13)
selected, some menu items may be greyed out and
are not selectable.
Test tone controls
The menu item
Test tone
enables you to
balance the volume levels of the speakers.
&
Select
Test tone
and press the cursor right.
é
Once turned on, the Test Tone will circulate
through the left, centre, right speakers and both
rear surround speakers (if present).
“
Press the cursor up/down to select the desired
speaker for individual volume level adjustment.
‘
Press the cursor left/right to adjust the volume
level.
Wireless Surround
The system has already been configured in the
factory to work properly.
In rare circumstances, interference from
external RF (wireless) equipment such as RF
headphones, mobile phones or remote controls
for lights, may occur.
Then it may be necessary to shift to another
wireless channel.
Use the cursor left/right, up/down to select
another channel.
Important
: Always be sure that the wireless
receiver box and the Wireless Surround setting
are switched to the same transmitting channel.
Otherwise no sound or only a distorted sound
will be heard on the surround speakers.
To avoid interfered picture the wireless transmitter
might be automatically switched off.
In rare cases, when no RF surround sound is
possible or when there is too much
interference, use the wired back up solution
with a 3.5 mm stereo jack. In this case select
Off
in the Wireless surround menu item. See
Connect Peripheral equipment,Wired rear
loudspeakers, p. 28.
To front / To surround
Select
To front
or
To surround
and then
select the distance between the TV or the rear
surround speakers and the place you sit to
watch TV.
Subwoofer
Select if you want to use the internal
subwoofer or if you installed an external one.
See Connect Peripheral Equipment, Connect
extra subwoofer, p. 28.
Auto Surround
Sometimes the broadcaster transmits special
signals for Surround Sound encoded
programmes.
The TV automatically switches to the best
surround sound mode when
Auto Surround
is
switched
On
. However it is possible to
overwrite this setting.
Speakers
8
Manual installation
Searching for and storing TV channels is done channel by
channel.You must go through every step of the Manual
Installation menu.
&
Select
Manual install
in the Install menu.
é
Press the cursor down.
Follow the instructions on screen.
Note: Search or direct selection of a TV channel.
If you know the frequency, the C- or S-channel number, enter the
3 or 2 digits of the frequency or the channel number directly with
the digit keys 0 to 9 (e.g. 048). Press the cursor down to proceed.
Repeat to search for another TV channel.
Manual install
Install
Selection mode
System
Programme
Search
Fine tune
Store
It is possible to change the name stored in the
memory or to assign a name to a TV channel for
which a name has not yet been entered. A name
with up to 5 letters or numbers can be given to
the programme numbers 0 to 99.
&
Select
Give Name
in the Install menu and
press the cursor down.
é
Select the programme number.
Note: keep the cursor up/down pressed to scroll
through the programme list quickly.
“
Press the cursor right.
A keyboard appears on the screen.
Press the cursor right to enter the keyboard.
Press the cursor up/down, left/right to select
the first character and press
OK
. Repeat for
every character you want to enter.
Select
Space
to enter a space;
Delete
to erase
the highlighted character in the name entered;
Shift
to display upper- or lowercase characters
on the keyboard;
Special
to display special
characters on the keyboard. Press
OK
to
confirm.
‘
Press the cursor left repeatedly when you have
finished the name giving.
(
Select another programme number and repeat
steps
“
to
‘
.
Give name
Reshuffle the programme list
p π
®
Space
®
Delete
A B C D E F G
1 2 3
H I J K L M N
4 5 6
O P Q R S T U
7 8 9
V W X Y Z
0
®
Shift
®
Special
You can change the order of the stored TV
channels.
&
Select
Reshuffle
in the Installation menu.
é
Follow the instructions on screen.
Select Favourite TV channels
&
Select
Favourite programmes
in the Install
menu.
é
Select your programme number with the
cursor up/down.
“
Select
Yes
or
No
with the cursor right.
‘
Repeat
é
and
“
for every TV channel or
external you want to make a favourite or a
non-favourite TV channel or external.
Give name
Install
VCR1
BBC1
BBC2
CNN
TVE
.....