Philips FaxJet 520, User Manual

24

Philips IPF 520 · 525 · 555

EN

5

Confirm with 

o

. The SMS is saved.

Printing SMSs

1

Press 

_

.

2

Using 

[

 select 

SMS RECEIVED

, 

SMS SENT

 or

SMS WRITTEN

.

3

Confirm with 

o

.

4

Select using 

[

DISPLAY LIST

.

5

Confirm with 

o

.

6

Using 

[

 select the SMS that you would like to print.

7

Confirm with 

o

.

8

Select using 

[

PRINT

.

9

Confirm with 

o

. The selected SMS is printed.

Print list of all SMS messages ljet 3

Deleting SMS

SMS Deletion Introduction

If the message memory is full, the device cannot receive
any more messages. Delete SMS messages to free up mem-
ory.
Your device can save 30 received SMSs, 5 composed and
sent SMSs and 5 templates, which are not yet sent.

1

Press 

_

.

2

Using 

[

 select 

SMS RECEIVED

, 

SMS SENT

 or

SMS WRITTEN

.

3

Confirm with 

o

.

4

Using 

[

 select 

DISPLAY LIST

.

5

Confirm with 

o

.

6

Using 

[

 select the SMS that you would like to delete.

7

Confirm with 

o

.

8

Using 

[

 select 

DELETE

.

9

Confirm with 

o

. The selected SMS is deleted.

Modifying the Settings

Changing Transmitting and Receiving 
Numbers

All numbers that you need to send and receive SMSs are
stored in your device. In case you moved to another tele-
phone service provider, you must change these numbers.

1

Press 

_

.

2

Using 

[

 select 

CONFIGURATION

.

3

Confirm with 

o

.

4

Select using 

[

SERV.CENTRE NO.

.

5

Confirm with 

o

. 

6

Select using 

[

TX SERV. CENTRE

.

7

Enter the number for sending SMS messages.

8

Confirm with 

o

. 

9

Select using 

[

RX SERV. CENTRE

.

10

Enter the number for receiving SMS messages.

11

Confirm with 

o

. 

12

You can exit with 

j

.

Switching off Audio Signal for SMS Recep-
tion

The reception of an SMS is indicated by a notification
tone. You can switch this notification tone off.

1

Press 

_

.

2

Using 

[

 select 

CONFIGURATION

.

3

Confirm with 

o

.

4

Using 

[

 select 

SMS RX ADVICE

.

5

Confirm with 

o

. 

6

Using 

[

 select whether notification tone for the re-

ception of SMS is to be on or not.

7

Confirm with 

o

. 

8

You can exit with 

j

.

Set the sub address (Terminal ID) of the 
device

Function is not supported in all countries and networks

(Function is not supported in all countries and
networks)

If you have several devices with an SMS function connect-
ed to one telephone line, you can assign sub-addresses to
these devices. You can then send SMS messages to a specif-
ic device. You can assign your  device it’s own sub address.

1

Press 

_

.

2

Using 

[

 select 

CONFIGURATION

.

3

Confirm with 

o

.

4

Select using 

[

TERMINAL NO.

.

5

Confirm with 

o

.

6

Enter the sub address.
The sender can send an SMS message directly to this
device by appending the sub-address to the telephone
number.

7

Confirm with 

o

.

Printing SMS Settings

1

Press 

_

.

2

Using 

[

 select 

CONFIGURATION

.

3

Confirm with 

o

.

4

Select using 

[

PRINT CONFIG.

.

5

Confirm with 

o

.

The settings are printed.

You can enter special characters using 

0

. 

Enter special characters using 

*

 or 

#

. 

Using 

f x

 switch the input area between small

and capital letters.
You can move the cursor using 

u

. 

Use 

C

 to delete individual characters. 

Press and hold 

C

 (at least two seconds) to delete

the entire text.

You can print a list of all SMS messages in the select-
ed folder, if you select 

PRINT LIST

 instead of

DISPLAY LIST

 using 

[

.