background image

FC9206

-  To open the appliance first remove the filter cover (item 31) 

and then remove the 5 screws from the appliance.

-  To remove the hinge, 

first remove the end caps 
(item 16) this can be done 
with a screwdriver, 
see picture.

-  When the end caps are 

removed, the hinging pin 
can be removed.

-  When this is done the hinge can be taken off the appliance.
-  Remove the can with the filters.
-  To remove the housing (7 screws) you will require for some 

screws a screwdriver with a 14.5 cm long shrank for this.
Screwdriver 4322 009 08490 for T15 can be used.

-  When the repair is finished, check whether all functions of 

the appliance work properly.

-  To disassemble the cord winder, use TORX screwdriver no. 

T10, which is one of a set consisting of T20; T15; T10; T9; 
T8; T7 and T6 (code number 4822 395 505145)

Further disassembly advise for the hinge:

- The chromium ornamental 

plate can be removed with 
a screwdriver (see picture) 
after that the min/max 
button and the On/Off 
button can be removed 
from the plate.

-  Remove the screw (

B

) underneath the ring with a T15 

screwdriver; the orange user panel (item 4) can be removed.

-  Choke assy can be taken out.
-  PCB can be removed.
-  To remove the sealing disk and the detector with the spring 

you have to remove the 2 screws (

C

) next to the sealing 

disk.

REPAIR INSTRUCTION

-  If the reel half spring unit is replaced, shaft 

L

 must be 

lubricated with silicone grease.  Do not apply any silicone 
grease to or spill any grease on terminals (item 46) or 
conductors (item 47).

-  The cord winder spring must be tensioned to the maximum 

level and the be rewound approx 1.5 turn.

-  Item 5, air valve, opens to cool the motor if the air 

displacement is too low or if the airflow is blocked.

-  If the function of the electronic control unit is not required, 

the Triac must be short-circuited in the manner shown in 
the circuit diagram.

ELECTRICAL DIAGRAM

DISASSEMBLY- AND  RE-ASSEMBLY ADVISE

Triac

Short-circuit

MOTOR
POWER
MODULE

Blue

Brown

CORD WINDER

Black

Blue

Brown

Black

M

Black

2-8

Summary of Contents for FC9206









Reviews: