15
English
3139 115 20143
Compact Disc
Playing a Disc
1
Press
É
to start playback.
➜
The disc tray, track number and elapsed
playing time of the current track appear on the
display.
¶
To interrupt playback, press
Å
.
➜
The playing time flashes.
¶
To resume playback, press
É
again.
2
To stop playback, press
Ç
.
Note:
– All the available discs will play once, then stop.
Disc Change
You can change the outer two discs while the
third inner disc is stopped or is playing.
1
Press
DISC CHANGE
.
➜
The CD changer tray slides out.
2
Replace the discs in the left and right disc trays.
¶
If you wish to change the inner disc during
playback, press
DISC CHANGE
again.
➜
"
DISC CHANGE
" will be displayed.
➜
The disc will stop playing.
➜
The CD changer tray will close to retrieve
the inner disc and then open again with the
inner disc accessible.
3
Press
OPEN•CLOSE
to close the CD changer
tray.
Selecting a desired track
Selecting a desired track when playback
is stopped
1
Press
í
or
ë
until the desired track appears
on the display.
2
Press
É
to start playback.
➜
The selected track number and elapsed
playing time appear on the display.
Selecting a desired track during playback
¶
Press
í
or
ë
until the desired track appears
on the display.
➜
The selected track number and elapsed
playing time appear on the display.
¶
If you press
í
once it will skip to the beginning
of the current track and play the track again.
Note:
– Pressing
í
during shuffling can only skip to the
beginning of the current track.
Searching for a particular
passage during playback
¶
Press and hold
à
or
á
until the desired
passage is located.
➜
The volume will be reduced.
¶
Play returns to normal when
à
or
á
is
released.
Programming Tracks
Programming tracks of a loaded disc is possible
when playback is stopped. The display will
indicate the total tracks stored in the
programme. Up to 40 tracks can be stored in
the memory in any order. When 40 tracks are
stored and you attempt to store another track,
the display will show “
FULL
”.
1
Load the desired discs in the disc trays.
2
Press
PROGRAM
to start programming.
➜
The
PROG
flag starts flashing.
3
Press the
CD
(CD 1•2•3) or
DISC 1/2/3
button to select the disc.
4
Press
í
or
ë
to select the desired track.
5
Press
PROGRAM
to store the track.
¶
Repeat steps
3
to
5
to store other discs and
tracks.
6
Press
Ç
once to end programming.
➜
The total number of tracks programmed and
total playing time appear on the display.
Notes:
– If the total playing time is more than “
99
:
59
“
or if one of the programmed tracks has a number
greater than 30, then “
--
:
--
” appears on the
display instead of the total playing time.
– If the system is reading the discs, programming
is not possible, “
READING
” will be displayed and
followed by "
DISC X
". "
X
" is the current read disc
number.
– During programming, if no button is pressed
within 20 seconds, the system will exit programme
mode automatically.
– “
SELECT A DISC
” will be displayed when
programming an empty disc slot.
Reviewing the programme
Reviewing of the programme is possible only
when playback is stopped.
¶
Press
í
or
ë
repeatedly to review the
programmed tracks.
¶
Press
Ç
to exit review mode.
pg 01-28/C200/21-Eng
29/05/2001, 10:13 AM
15
