GAME PORT
TEST
STEP
1
2
3
4
5
DISPLAY
(SCROLL ONCE)
ACTION
Select CD as background sound source. Press PLAY to play the track.
Select TUNER as background sound source.
Select PC-LINK (for set with PC-LINK) as background sound source.
Press PLAY to play the track.
Select AUX as background sound source.
No mixing.
Disconnect mains cord to exit
MIX-CD
MIX-TU
MIX-USB
MIX-AUX
MIX-OFF
Choose desired
background source
by pressing button
" MIX-IT "
GAME
Button pressed?
Y
N
Display shows "GAME PORT"
MIX-IT
Button pressed?
Y
N
Table 3A
Error code
E1000
E1001
E1002
E1003
E1005
Error Description
Focus Error
Triggered when the focus cannot be found within a certain time when starting up the CD, or if the focus
is lost for more than a certain time during playing of CD.
Radial Error
Triggered when the radial servo is off-track for a certain time during playing of CD.
Sledge In Error
The sledge did not reach its inner position (inner-switch is still close) before approximately 6 seconds
have passed by. Inner-switch or sledge motor problem.
Sledge Out Error
The sledge did not come out of its inner position (inner-switch is still open) before approximately 250ms
have passed by. Inner-switch or sledge motor problem.
Jump Error
Triggered in normal play when the jump destination could not be found within a certain time.
Table 3B
Error code
E1006
E1007
E1008
E1020
E1061
E1079
Error Description
Subcode Error
Triggered when a new subcode was missing for a certain time during playing of CD.
PLL Error
The Phase Lock Loop could not lock within a certain time.
Turntable Motor Error
Generated when the CD could not reached 75% of speed during start-up within a certain time. Disc
motor problem.
Focus Search Error
The focus point has not been found within a certain time.
The tray could not enter the inside position and is opening again. This can happen if the tray is blocked
such that it cannot go fully inside, or if the 5DTC control module is defective and never closes.
The tray could not reach the outside position and is stopped at its blocked position. This can happen if
the tray is blocked such that it cannot go fully outside, or if the 5DTC control module is defective and
never opens.
STANDBY ON
Button pressed?
Y
N
Set is in Service PLAY Mode
CD
Button pressed?
Y
N
The Service Play Mode is intended
to detect and identify the failures
in the CD Mode.
In this mode the DTC works as in
normal operation. The electronics
will still function even when an error
is detected so that repair activities
can be carried out.
SERVICE PLAY MODE
(For non MP3 set only)
DTC works as in normal operation.
In case of failures, error
codes according to Table 3A and
Table 3B will be displayed.
Display shows "5DTC-Vnn" -
Version of 5DTC control software
(nn = Version Number).
CD
Button pressed?
Y
N
5DTC CONTROL &
MP3 CD MODULE
TEST
(For MP3 set only)
STEP
1
2
**3
**4
**5
**6
**7
DISPLAY
MESSAGE
-
-
-
BUS OK
-
-
FOC OK
5DTC-ER
-
-
BUS ER
-
-
FOC ER
ACTION
Version of the 5DTC control software (nn = Version Number).
Indicates the module used.
Version of the MPEG software (nn = Version Number).
Communication test between the Main uP and CD Module
CD SLEDGE MOTOR is moved in.
CD SLEDGE MOTOR is moved out.
FOCUS SERVO Test.
Press
9
to exit
OKAY
ERROR
5DTC-Vnn
MP3CD’02
TI-Vnn
TI BUS
TI SLD I
TI SLD O
TI FOC
** Choose
level
by pressing
Q
R
Note : Disc should be available on the tray before entering the Service Test Mode.
To start service test program
hold
™
& AUX
depressed while
plugging in the mains cord
Display shows the
ROM version
"S-Vyy"
(Main menu)
S refers to Service Mode
V refers to Version
yy refers to Software version number of the uProcessor
(counting up from 01 to 99)
SERVICE TEST PROGRAM
Mini 2003_FW-C/M 5xx/7xx_Service Test Program (dd wk0306)
3-2
3-2
Summary of Contents for FW-M589
