background image

M

D

A

T

H

I

J

U

V

A

 Hanger hook

D

 Air vent slide

U

 Steamer power-on button with light

V

 Blowing/suction button

T

 Steam activator

H

 Board tilting button

I

 Height adjustment lever

J

 Locking strap

M

 Mains plug

Steaming

 

E

Steaming tips and tricks

• 

The steamer is perfect for all delicate fabrics, such as silk, wool and cashmere.

• 

To steam a jacket, put it directly on the board. To steam a blouse or a dress, use the hanger hook 

A

.

2

Put the mains plug 

M

 in an earthed 

wall socket. The power-on light goes on.

Fill the water tank.

You can use normal tap water.

Undo the locking strap 

J

 and unfold 

the ironing board to vertical position.

Set both air vent slides 

D

 to the 

ironing position.

Take the steamer out of the 

steamer compartment. 

Press the steamer power-on button 

U

 

to switch on the steamer. The power-

on light goes on.

After approx. 2 minutes the steamer is 

ready for use.

Press the steam activator 

T

.

Never direct the steam at people.

If you want to use the blowing 

function, press the blowing button on 

the steamer.

If you want to use the suction function, 

press the suction button on the steamer. 

You can easily hang the steamer on the 

board handle 

G

 when necessary. 

You can store the hot steamer in the 

heat-resistant storage compartment 

immediately after you have switched 

off the steamer.

1

2

3

4

5

6

7

Summary of Contents for GC9930/07









Reviews: