Philips HTS5200, Service Manual

2 - 1

2 - 1

System , Region Code , etc. Setting Produre

6) Upgrading new software

a) Copy the latest upgrading software onto a CD-R or USB storage 

device

b) Insert the CD-R program disc or connect the USB storage device 

to the home theater

c) TV will show message as follow

d) Select <OK>,the home theater will start to upgrading 
automatically

Note: when upgrade in progress, please do not unplug or switch off 
the device.
when the updated is complete ,the home theater automatically 
switch to standby. 

7) Produce to change Tuner grid (for /98)

 Only applicable for certain regions, in some countries, the 

frequency step between adjancent channels in the FM hand is 

50KHZ(100KHZ in some areas)

a) Press<radio> on R/C to select “FM”

b) In “FM” playbak mode,press & hold< play/pause> button until 

“grid 9” or “grid 10” appears

Note: repeaing the same action will toggle back to it  previous 

tunning grid setting.

* “grid 10” is default for /55/98 version.

8)How to replace the defective DVD Loader

a) Remove the defective DVD Loader (see chapter 3).

b) Accordingly connect DVD Loader and “CN802”, “CN803”, 

“CN801” on the top of main board as shown below:

CN802

CN801

CN803

   CAUTION!

 This information is confi dential and may not be 
distributed.Only a qualifi ed service person should 
reprogram the Region Code.

Upgrade fi le detected 
Do you wish to continue with
the software upgrade?

          OK              Cancel

Current model:            5200-12/98/51
Version:00.08.00_1       Release:2009.12.16
Region: 2                      Servo:D1.72.01.00
8032:  05.00.04.06        Risc:  BB.00.00.00
MCU: 06.01     Touch: 0044     Dock: Error

if current model doesnot match your set,
use down arrow key on the remote to change
                              OK

c) Remove solder joint on the ESD protection point.

The ESD protection point 

on the top side view of OPU 

The Top side view of OPU  

Note: The ESD protection point on any one side must be soldered if

  - the DVD Loader is OK and needs to be disconnected from 

connector CN802, CN803 and CN801 of the main board.

  - the defective DVD Loader is needed to be send back to supplier 

for failure analysis and to support back charging evidence.

1)Restore factory setting

a) Press <SETUP> button on R/C

b) Select <preference setup> ,then press < OK >

c) Select <default>,then press <OK> to confi rm

2)Region code change  

a) Open the Door,then,press “1” “5” “9” on RC

b) Press <OK> button on RC

c) TV will show message as follow:

d) If current model doesnot match your set, use down arrow key on 

the remote to change.

3)Password change 

a) Press <SETUP> button on R/C

b) Select <preference setup> ,then press <OK>

c) Select <password> <change>,then press <OK> to confi rm

“0000” is default password supplied.

4)Trade model

a) Press <Open/Close>button on R/C

b) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA 

OFF“

5)Check on software version

a) Press <SETUP> button on R/C

b) Select <preference setup> ,then press <OK>

c) Select <version info>,then press <OK>

d) TV will show message as follow:

      Preference setup
     Version Info.

 Current model:                 5200-12/98/51
 Version :00.08.00_1         Release: 2009.12.16
 Region:  2                        Servo:    D1 .72.01.00
 8032:05.00.04.06             Resc:     BB.00.00.00
 MCU:    06.01                  Touch:   0044
 
                                OK
    
 Press SETUP  to exit menu