Circuit Description
EN 60
9.
9.
Circuit Description
Index:
1.
Introduction
2.
Audio Signal Processing
3.
Video Signal Processing
4.
Synchronisation
5.
Deflection
6.
Power Supply
7.
Control
8.
Abbreviations
Note:
•
Figures can deviate slightly from the actual situation, due
to different set executions.
•
For a good understanding of the following circuit
descriptions, please use the block diagram in chapter 6, or
the electrical diagrams in chapter 7. Where necessary, you
will find a separate drawing for clarification.
9.1
Introduction
The L01 chassis is a global TV chassis for the model year 2001
and is used for TV sets with screen sizes from 14” to 21” (small
screen) and 21” - 34” (large screen), in Super Flat and Real Flat
executions.
The standard architecture consists of a Main panel, a Picture
Tube panel, a Side I/O panel and a Top Control panel. In some
executions, a Picture In Picture (PIP) panel is used.
The Main panel consists primarily of conventional components
with hardly any surface mounted devices.
Figure 9-1
The functions for video processing, microprocessor (
µ
P) and
teletext (TXT) decoder are combined in one IC (TDA958xH),
the so-called Ultimate One Chip (UOC). This chip is (surface)
mounted on the copper side of the LSP.
Figure 9-2
The L01 is divided into 2 basic systems, i.e. mono and stereo
sound. While the audio processing for the mono sound is done
in the audio block of the UOC, an external audio processing IC
is used for stereo sets.
The tuning system features 100 (or 125) channels with on-
screen display. The main tuning system uses a tuner, a
microcomputer, and a memory IC mounted on the main panel.
Also, in some type numbers, an FM radio is implemented with
40 pre-set channels.
The microcomputer communicates with the memory IC, the
customer keyboard, remote receiver, tuner, signal processor IC
and the audio output IC via the I
2
C bus. The memory IC retains
the settings for favourite stations, customer-preferred settings,
and service/factory data.
The on-screen graphics and closed caption decoding are done
within the microprocessor, and then sent to the signal
processor IC to be added to the main signal.
The chassis uses a Switching Mode Power Supply (SMPS) for
the main voltage source. The chassis has a ‘hot’ ground
reference on the primary side and a cold ground reference on
the secondary side of the power supply and the rest of the
chassis.
9.2
Audio Signal Processing
9.2.1
Stereo
In stereo sets, the signal goes via the SAW filter (position 1004
in case of QSS demodulation and 1003 in case of Intercarrier
demodulation), to the audio demodulator part of the UOC
IC7200. The stereo audio output on pin 33 goes, via TS7201,
to the stereo decoder 7831.
The switch inside the stereo decoder 7831 selects (via I
2
C)
either the internal decoder or an external source.
The NICAM + 2CS AM/FM stereo decoder is an ITT MSP34X5.
The output is fed to the to the audio amplifier (AN7522 at
position 7901). The volume level is controlled at this IC (pin 9)
by a control line (VolumeMute) from the microprocessor. The
audio signal from 7901 is then sent to the speaker/headphone
output panel.
Figure 9-3
TUNER
VBAT
AUDIO
12V
3.9V
3.3V
FM IF
BUFFER
VIDEO SOURCE
SELECTION
RF ANT.
FM ANT.
EXT. AUDIO
INPUT
7801
FM
FMR
AUDIO SOURCE SELECTION
CONTROL
EXT. AUDIO OUT
7861
7831
7834
7835
7209
7210
7901
10
1000
0265
11
1
1
1
AGC
1200 : 1202
18
19
22
23
33
47
24
25
24
38
INT_CVBS
EXT_CVBS
40
42
16
17
15
30
68
I2C
50:53
EXT RGB/YUV INPUT
56:58
7330
EHT
7460
H
EW
V+
V-
7471
7602
7200
SIF
VIF
POWER
SUPPLY
CL 16532008_039.eps
220501
AUDIO
AMPL.
SAW
FILTER
SAW
FILTER
SOUND
IF
DEMOD.
AUDIO DECODING
AND
PROCESSING
SELECTION
MATR. SWITCH
VISION
IF
DEMOD.
NVM
VIDEO
AMPL.
HOR.
DEFL.
+
EW
VERT.
DEFL.
µ
P
VIDEO
PROCESSING
RGB/YUV
PROCESSING
SYNC
PROCESSING
SOUND
TRAP
VIDEO
SWITCH
EXT. VIDEO
INPUT
7802
Summary of Contents for L01H.1A
