3-3
Procedure for check Software version
1) Select Disc with the Remote Control
2) Press <SYSTEM MENU>
3) Use the down key move all the way down (4x) to
bottom of "Setup Menu".
4) Use the right key move to the sub-menu.
5) Use the down key move down (3x) to "Help text" and
down one more time to see the software version.
6) The TV screen will shows:
..... 5.1.10 030807P22204208 7.10.0 7.2
where 5.1.10 = Backend (DVD) software version
030807 = date of Backend software
22204208 = DVD version matrix
7.10.0 = Basic Engine (Servo) software version
7.2 = 5DTC software version
7) Press <OK> three times to exit.
Procedure to upgrade software
1) Power up the set and open tray Disc 1.
2) Place upgrade CD-ROM onto tray and close.
3) The set will display "DOWNLOAD" and the TV screen
will go blank.
4) The TV screen turns on again and Tray Disc 1 will
open.
5) Remove the upgrade CD-ROM and unplug the Mains
supply.
6) The whole process should last less than 10 minutes.
Caution:
This information is confidential and may not be distributed. Only a qualified service person
should reprogram the mono BE board.
After replacement/repair of the Mono BE board, the customer settings and also the region code may be lost.
Reprogramming will put the set back in the state in which it has left the factory, i.e. with the default settings
and the allowed region code.
Reprogramming will be done by way of the Remote Control.
Put the player in stop mode, Disc 1 with no disc loaded.
Do the following steps with the Remote Control:
1) Press
<DISC MENU>
followed by numerical keys
<1> <5> <9>
The set display shows:
- 0 - 0 - 0 - 0 -
2) Press now successively the following numerical keys :
for MX5800SA/21R :
<3><2><3> <0><4><0> <0><8>
AP
for MX5800SA/21S :
<4><2><3> <0><4><0> <0><8>
Australia, New Zealand
for MX5800SA/22S :
<2><2><2> <0><4><2> <0><8>
Europe
for MX5800SA/33S :
<3><2><3> <0><4><1> <0><8>
AP - Korea
for MX5800SA/35S :
<6><2><3> <0><4><0> <0><8>
China
for MX5800SA/78
:
<3><2><3> <0><4><1> <0><8>
Latam
for MX5900SA/37
:
<1><1><1> <0><4><3> <0><8>
US
3) Press
<DISC MENU>
again. The set display will show:
DONE
.
Caution: The set needs about 3 seconds to reset to required setting.
4) Disconnect mains to ensure proper reset.
Reprogramming of DVD version matrix
Summary of Contents for MX5800SA
