background image

EN

G

LI

SH

11

How to Do More

3.2 

How to Do a Range Check

If the Remote Control and the Extender are too far apart, the signal will be out of range.  
You can do a range check on the Remote Control. 

D

 Note

If no Extender is defined in the Configuration Program, the Range Check Extenders option 
will not be presented in the Service Menu. 

1

  Press 

 and 

 for 3 seconds to enter the Service Menu.

2

  Choose the option 

Range Check Extenders

.

The Range Check screen appears: 

 
  

3

  Select 

Back

 to return to the Service Menu.

3.3 

How to Avoid Interference from Other Remote Controls

If the 

busy LED

 on the Extender is blinking without the Remote Control sending commands, 

the Extender picks up signals from another Remote Control on the same channel. You can 
solve this problem by changing the channel.
You configure the channel in the 

Link Extenders to components

 step of the New Project 

Wizard and on the Extender. All Remote Controls and RF Extenders need to be defined on 
the same channel. Three channels (from 1 to 3) can be assigned.

1

  Choose a channel on the Extender by sliding the Channel switch.

2

  In the 

Link Extenders to components

 step of the New Project Wizard, choose the 

same channel.
Refer to the Configuration Program’s Online Help for more information.

3

  Try to operate your devices with the Remote Control.

No range

Low range

Medium range

High range

Summary of Contents for Pronto RFX9200/37



















Reviews: