Philips RFX600099 User Manual Download

Page: 8 / 8

User Guide

Specifications

The specifications and design of this product are subject to change without notice.

Hardware

Red LED (continuously on when powered, blinking during RF reception)

16 IDs and 4 CHs

4 outputs for IR emitters

Possibility to have multiple RF extenders in one home not interfering

Positioning: freestanding, mounted horizontally or hanging up side

down

Dimensions

4.5 x 3.2 x 1.2 inch (113 x 81 x 30 mm)

Operating

32°F to 122°F (0°C to 50°C)

temperature

Infrared (IR)

Operating distance: up to 16 feet (5 meters)

IR frequency range: DC/flash codes, 36kHz-550kHz

Radio

Operating distance: up to 100 feet (30 meters)

frequency (RF)

depending on the surrounding conditions

Frequency: 418 MHz (US)

Dual IR emitters

Number of IR emitters: up to 8 (4x2), emitters wired in series

3.5mm mono mini-plug

Cable length: 10 feet (2.5 meters)

Max. range: 3 feet (75 cm)

Accessories

120V AC Power adapter (400mA/12V DC adapter, UL-approved)

Mounting kit (Plate and 4 screws)

Approvals

The device complies with part 15.19(a)(3) of the FCC Rules.

Operation is subject to the following two conditions: (1) this device

may not cause harmful interference and (2) this device must accept

any interference received including interference that may cause

undesired operation.

Philips Consumer Electronics Company,

Knoxville, Tennessee 37914 – 1810 U.S.A.

Specifications

RFX6000 new 24-07-2002 14:04 Pagina 8

Summary of Contents for RFX600099









Search results

Summary of Contents for RFX600099

Reviews:

Related manuals for RFX600099

Brands by name

Popular brands

Philips RFX600099, User Manual

Search results

Summary of Contents for RFX600099

Reviews:

Related manuals for RFX600099

Brands by name

Popular brands