5
RP421- page 5
English
8
TELETEXT FUNCTIONS
b
- Teletext on/off _ _ _ _ _ _ _ _ _ _ _ _
f
- Page hold
e
- Reveal/conceal
c
- TV-teletext mixed
z
- Actual time on screen
a
- Cancel teletext picture temporarily
h
- Enlarge _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
õ
- Memory out
ö
- Enter
`
- TV-mode
English
With side button
1
pressed:
8
PIP (PICTURE IN PICTURE)
FUNCTIONS
n
- PIP on/off
o
- PIP shift
r
- PIP freeze
p
- PIP swap
q
- PIP select
t
- Multi-picture display
8
SOUND FUNCTIONS
4
- First or second language
>
- Spatial sound effect
I
- Speech/Music
∞
- Crispener
English
ADDITIONAL
8
-
NQ
- Install
9
-
†
- (Video) input/output_ _ _ _ _ _ _ _
0
-
û
- Personal Preference
!
- miscellaneous
_
- Sleeptimer
J
- OSD/ 1-12
÷
- Previous Program
13/24
- 13-24
With side button
1
pressed:
9
-
†
2 - (Video) input/output 2
0
-
·
- Automatic search tuning
!
- miscellaneous
- Programmable:
A
- PIP step up
A
-
B
- PIP step down
B
-
C
- Movie expand
C
-
D
- DNR
D
-
SETTING UP YOUR VCR
This remote is ready to work with any Philips VCR. For other brands, it needs to be set up first.
That only takes a couple of seconds, thanks to Philips’ Simple System Setup!
Before you start,
make sure the equipment is switched on. Sit right in front of it.
If you know the brand of your VCR
, look at the code list at the back of this book, and find the
first 3-digit code for your equipment.
1.
Press and hold ‘Menu’ and ‘7’ simultaneously for at least 3 seconds.
2.
Enter the 3-digit code using the keypad.
That’s it!
Now, press a few keys on the remote to check that the equipment responds correctly. If
it doesn’t, try again using the next code in the list. In the rare instance that none of the codes
work, follow the instructions below.
Tip:
Make a note of the code on the back of the remote and in the back of this booklet in case
you ever need to setup again.
If you don’t know the brand of your VCR
or if you can not find it in the codelist, setup still
won’t take long. Philips’ patented Handsfree autosearch tests all the codes one after another and
finds the right one for you! Maximum search time is 3 minutes for VCRs.
Make sure the VCR is switched on, insert a tape and start playback. You will know when
the correct code has been found because the VCR will stop playback.
1.
Press and hold ‘Menu’ and ‘7’ simultaneously for at least 3 seconds.
2.
Press
y
to start the search. Keep the remote pointed at your VCR. Every 1.5 seconds
another code is sent. When the right code is found, the VCR either switches off or will
stop playback).
3.
Immediately press
y
to stop the search.
If you missed the correct code
because the search went too far, switch the VCR back on
and start playback again, then press - P to send the previous code again. Keep pressing - P
until the VCR stops playback again.
4.
Once you’ve found the correct code, press
y
to lock it in memory.
That’s it!
Now, switch the VCR manually on again, then press a few keys on the remote to
check that the VCR responds correctly. In the rare instance that it doesn’t, try again from
step 1 to find a better code.
TELETEXT/PIP
