2.5.2 If you don't know the brand name
If you don't know the brand name of your equipment or if you cannot find it in
the code list, set-up still won't take long. Philips' patented Hands-free
Autosearch tests all the codes one after another and finds the right one for you!
Make sure the TV is switched on. You will know the correct code has been found
when the equipment switches off. Then:
1
Press the SMART key (for about three seconds) until the LCD displays
TIMER
. Release the SMART key.
2
Press Cursor up or Cursor down until the LCD displays
SETUP
.
3
Press OK.
– The LCD displays
ENTER CODE
. The SBC RU880 is now in set-up mode.
4
Press Cursor up or Cursor down until the LCD displays
AUTOSEARCH
.
5
Press OK.
– The SBC RU880 is now in programming mode and the LCD displays the
selected equipment.
6
Press Cursor up or Cursor down until the LCD displays
TV
.
7
Press
B
to start the search.
– Each time a code is transmitted it is displayed on the LCD. There is a 1.5
second period between each transmission. When the right code is found, the
TV switches off.
8
Immediately press
B
to stop the search.
– The LCD displays the selected equipment and its code.
If you missed the correct code because the search went too far, switch the TV
back on, then press (P-) to send the previous code again. Keep pressing (P-)
down repeatedly until the equipment switches off again
9
When you've found the correct code, press OK to lock the code in the SBC
RU880’s memory. The LCD will then display
TV2
. When you press the TV
mode key the LCD will display
TV1
.
That's it!
Now switch the second TV on again manually, then press a few keys
on the SBC RU880 to check that the TV responds correctly. If it doesn't, try
again from step 1 to find a better code.
NOTE:
When the SBC RU880 has searched all codes, the LCD displays
END
for a
few seconds before returning to normal operation.
2.6 TO CONTROL THE SECOND TV'S VOLUME
If you have installed a second TV under the HOME mode, you can also control
that TV's volume when you are in VCR mode. To do this:
1
Press and hold the SMART key (for about three seconds) until the LCD
displays
TIMER
. Release the SMART key.
2
Press Cursor up or Cursor down until the LCD displays
SPECIAL
.
3
Press OK.
– The LCD displays
THEATRE
.
4
Press Cursor up or Cursor down until the LCD displays
COPY VOL
.
5
Press OK.
– The SBC RU880 is now ready to change the volume, and the LCD displays
FROM
.
6
Press the mode you want to copy the volume from (in this case HOME).
–
TO
appears on the LCD.
7
Press the mode you want to copy to (in this case VCR).
– The SBC RU880 goes back to normal mode.
NOTE:
The SBC RU880 does not react to keys other than the keys described above.
To go back to normal mode press the SMART key.
2.7 RESTORING DEFAULT KEY SETTINGS
2.7.1 If you want to restore the original function of a specific key
1
Press and hold the SMART key (for about three seconds) until the LCD
displays
TIMER
. Release the SMART key.
2
Press Cursor up or Cursor down until the LCD displays
SPECIAL
.
3
Press OK.
– The LCD displays
THEATRE.
4
Press Cursor up or Cursor down until the LCD displays
RESET
.
5
Press OK.
– The SBC RU880 is now in reset mode and the LCD displays
RESET KEY
.
6
Press OK.
– The LCD displays
PRESS KEY
.
7
Press the key that you want to restore.
– The LCD displays
OK
for a second and then returns to normal operation.
That's it!
The key now operates under its original function.
English
9
