background image

15

8b.

Open Group

Luminaire

Luminaire

Point remote to  

any

 luminaire  

and press  
“open,” once.

Luminaire

Wait for the the entire 
luminaire group to dim 
down to 5%.

Make sure the button is pressed only once. Pushing multiple times 
can create multiple networks which can cause undesired operation.

8c.

Link the scene selector

Step 

8c

 is a trial and error process. The 4 buttons signify 4 di

ff

erent 

wireless channels. To join the scene selector to the luminaire group 
the wireless channel of the scene selector and the luminaire must 
match. Since the wireless channel of the luminaire is not visible, one 
has to try out all the 4 channels via the buttons to determine the 
matching channel as described in step 

8d

10 sec.

If the switch joins 
the group then the 
luminaire will FLASH 
twice and group light 
level will go to 5%.

Select the correct wireless channel  
by pressing and holding one of the  
4 buttons for at least 10 seconds and 
then release the button. 

Luminaire

8d.

Program the scene selector

10 sec.

10 sec.

10 sec.

or

or

or

or

If the switch joins 
the group then the 
luminaire will FLASH 
twice and group light 
level will go to 5%.

If the switch did not join the group as  
per step d then repeat step d but with  
a di

ff

erent button (1) this time.

Luminaire

Summary of Contents for SpaceWise

































Reviews: