— 23 —
1
Select VCR Set Up Mode
1 Press
PLAY
5 or
STOP
∞ to select
“VCR SET UP”
then press
OK/
STATUS
.
2
Set Record Link
1 Press
PLAY
5 or
STOP
∞ to select
“AUTO SAT RE-
CORD LINK” ,
then press
FF
3
to set to “ON” .
3
Finish Setting
Press
MENU
.
The following message will appear:
Press
POWER
to turn off the VCR.
If you do not turn off the VCR after
30 seconds, the VCR will turn off
automatically.
The VCR will then move to stand-by
mode and "L-1" will blink on the
display panel.
Notes:
• Pressing the POWER button while Record
Link or stand-by mode is in progress will
cancel the REC LINK mode and "AUTO
SAT RECORD LINK" is set back to
"OFF" automatically.
• Be sure not to turn on the satellite tuner
before the program is executed otherwise
the VCR will start recording when the
satellite tuner's power is turned on.
• Depending on the type of satellite tuner,
the VCR may not record a slight portion
of the beginning of the program or may
record slightly longer than the actual
length of the program.
• While the VCR is in Record Link or stand-
by mode, normal timer recording will not
perform.
• “Err L-1” will appear if you engage the
Record Link during the satellite tuner
power is on. Turn off the satellite tuner.
However, if “Err” will not disappear even
though the satellite tuner is turned off,
Record Link function will not work
properly with that satellite tuner.
Record Link
This facility allows you to record a
satellite program automatically which
is timer-programmed on your external
satellite tuner. Connect a satellite tuner
to the VCR's AUDIO/VIDEO IN jacks
on the rear panel and programme the
timer on the satellite tuner. The VCR
starts recording when it signals input
from the satellite tuner to the VCR's
AUDIO/VIDEO IN jacks on the rear
panel, and when there is no input signal
the VCR stops recording and the power
shuts off.
Before performing the following steps:
• Make sure the satellite tuner is connected
to the VCR's AUDIO/VIDEO IN jacks on
the rear panel.
• Programme the timer on the satellite
tuner.
• Insert a cassette with the safety tab in
place.
VCR SET UP
TUNER SET UP
INITIAL SET UP
TAPE MANAGER
SELECT: CONFIRM: OK
END: MENU
PLEASE FOLLOW THE STEPS
BELOW:
1 SET PROGRAM ON SAT
2 TURN SAT OFF
3 TURN VCR OFF
DSPC
ON
ON SCREEN MODE ON
TIMER REC SPEED MANUAL
AUDIO OUT HIFI
AUTO SAT
RECORD LINK OFF
S-VHS MODE
ON
SELECT: CHANGE:
END: MENU
Turbo Timer
This function allows you to set the
timer recording program without going
through the regular set up with the on
screen. The extent of programming is
24 hours from the current time.
1 Insert a tape into the VCR and press
the “TURBO TIMER” button on the
remote control. Current time will
appear on the display panel.
2 To change the START time, press the
PLAY
5 or
STOP
∞ ( if you press
and hold the button, the time changes
in 30-minute increments) then press
OK/STATUS.
3 To change the STOP time, press the
PLAY
5 or
STOP
∞ ( if you press
and hold a button, the time changes
in 30-minute increments) then press
OK/STATUS.
4 To change the CHANNEL number,
press the
PLAY
5 or
STOP
∞, then
press
OK/STATUS.
5 The data input will be memorized
and the Turbo Timer mode will be
finished so that normal display
appears.
6 Turn off the VCR.
Notes:
• To exit Turbo Timer mode at any step,
press the TURBO TIMER button.
• If “Err” appears on the display panel,
all eight programs have been set and
Turbo Timer will not proceed. To
remove the error message, press the
TURBO TIMER button again.
• Settings of Turbo Timer will appear
on the display panel only and not on
the screen.
• Programs Overlap Warning does not
function with Turbo Timer.
• DAILY or WEEKLY programming
are not available on Turbo Timer.
• Tape speed can be selected anytime
during steps 2 through 4.
SP
SP
SP
L
SP
vr1010/75
00.6.29, 4:54 PM
23
