— 25 —
Timer Recording
To record while you’re away, follow step
1 — 9 below. For each programme you
set, the VCR will turn on, start recording,
and turn off automatically. You can store
up to 8 programmes.
Make sure....
• The clock is set to the correct time
before setting timer recording.
• A cassette is inserted in the VCR and
the record tab of the cassette must
not be removed.
• The remote control operation mode
is set correctly for operating your
target component.
– Press
VCR
to operate the VCR.
– Press
TV
to operate the TV.
FOR EACH STEP BELOW, YOU
NEED TO FINISH WITHIN 60
SECONDS; OTHERWISE,
PROGRAMMING WILL HAVE TO
BE RESTARTED FROM STEP 1.
1
Select Timer Mode
1 Press
VCR
.
2 Press
TIMER
.
The Timer
Recording menu
appears.
2
Select Programme mode
1 Press
PLAY
5 or
STOP
∞ to select
“QUICK PROG-
RAMMING” then
press
OK/STAT-
US
.
The Quick Programming menu
appears.
• If you have already made 8
programmes, “ALL PROGRAMS IN
USE” appears and goes back to the
Timer Recording menu. If this
happens, delete unwanted programmes.
(
✈
P.20)
3
Select Channel
Press
CH
5 or ∞ to
enter the TV channel.
• Holding down
CH
5
or
∞ rapidly scans
through the channels.
• To record from exter-
nal line input, press
CH
5 or ∞
until
“A/V REAR” or “A/V FRONT” appears.
3
Select Tape Speed
Press
ALT/SPEED
.
• Each time you press
the button, the tape
speed alternates bet-
ween “SP”, “LP”, or
“SLP”.
SP, LP : For PAL signal
SP, SLP : For NTSC signal
• To change the stop time, press
STOP +/–
(number 2 or 5 button).
4
Confirm Programme
Press
OK/STATUS or TIMER
.
“PROGRAM WAS COMPLETED”
appears on the TV screen.
After 5 seconds, the above message
disappears, and the normal TV picture
resumes. The
(timer) indicator
lights up on the display.
• If “PROGRAM NOT COMPLETED”
appears, try again from step 1.
• If “ PROGRAM OVERLAPPED”
appears, the timer recording you just
programmed overlaps another timer
recording. The Program Review screen
will appear with a magenta line blinking.
To change any item on the overlapping
programs, see page 20.
If you want to store other
programmes, repeat steps 1 to 4
5
Finish the Settings
Press
POWER
to turn off the VCR.
The VCR must be turned off for a timer
recording to take place. If you forget to
turn off the VCR, “PLEASE TURN
OFF VCR FOR TIMER
RECORDING” flashes on your TV
screen two minutes before a timer
recording starts. To remove the
message, press the
CLEAR
button.
If you want to record the same
programme daily, press
DAILY
(Number button 8) at step 3 (Press the
button again to cancel).
The VCR will record a TV programme
every day (Monday through Friday) at
the same time and length. (Daily
Recording)
If you want to record the same
programme weekly, press
WEEKLY
(Number button
9
) at step 3 (Press the
button again to cancel).
The VCR will record a TV programme
once a week at the same day, time, and
length. (Weekly Recording)
If you want to cancel the currently
set programme, press
CLEAR
.
Note:
• Even if a power failure occurs, the VCR
keeps your timer programs. However, the
clock time and other menu settings are
lost if it lasts for more than 10 minutes.
As a result, when the power is supplied
again to this VCR after the power failure,
set the clock time and turn off the VCR.
Each timer program you have made will
start unless its start time already passes.
G-CODE/SHOWVIEW
QUICK PROGRAMMING
PROGRAM REVIEW
SELECT: CONFIRM: OK
END: TIMER
ONE TIME PROGRAM
PROGRAM 1
/–
START +/– – –:– – AM
STOP +/– – –:– – AM
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
– –
ONE TIME PROGRAM
PROGRAM 1
/– 12
START +/– – –:– – AM
STOP +/– – –:– – AM
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
ONE TIME PROGRAM
PROGRAM 1
/–
START +/– 08 : 00 PM
STOP +/– 10 : 00 PM
REC SPEED LP
DATE +/– 14/07/00
FRIDAY
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
12
vr1010/75
00.6.29, 4:54 PM
25