—19—
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
This function allows you to set the timer record-
ing program without going through the regular set
up with the on screen. The extent of program-
ming is 24 hours from the current time.
1 Insert a tape into the VCR and press the
“TURBO TIMER” button on the remote
control. “ ” (start time prompt) and the
current time appears alternately on the display.
2 To change the START time, press the
PLAY
5
or
STOP
∞ button (if you press and hold
either button, the time changes in 30-minutes
increments), then press
OK/STATUS
.
Then,“
” (stop time prompt) and the set
start time appears alternately on the display.
3 To change the STOP time, press the
PLAY
5
or
STOP
∞ button (if you press and hold
either button, the time changes in 30-minutes
increments), then press
OK/STATUS
.
Channel number will appear on the display.
4 To change the CHANNEL number, press the
PLAY
5 or
STOP
∞, then press
OK/STA-
TUS
.
5 The data input will be memorized and the
Turbo Timer mode will be finished so that
normal display appears.
6 Turn off the VCR.
Notes:
• To exit Turbo Timer mode at any step, press the
TURBO TIMER button.
• If “Err” appears on the display panel, all eight
programs have been set and Turbo Timer will not
proceed. To remove the error message, press the
TURBO TIMER button again.
• Settings of Turbo Timer will appear on the display panel
only and not on the screen.
• Programs Overlap Warning does not function with
Turbo Timer.
Turbo Timer
9
Finish Settings
Press
POWER
f
to turn off the VCR.
The VCR must be turned off for a timer
recording to take place. If you forget to turn off
the VCR, “PLEASE TURN OFF VCR FOR
TIMER RECORDING” flashes on your TV
screen two minutes before a timer recording
starts. To remove the message, press the
CLEAR
button.
If you want to record the same programme
daily, press
DAILY
(Number button 8) during
step 3 through 7. (Press the button again to
cancel).
The VCR will record a TV programme every day
(Monday through Friday) at the same time and
length (Daily Recording).
If you want to record the same programme
weekly, press
WEEKLY
(Number button 9)
during step 3 through 7. (Press the button again
to cancel).
The VCR will record a TV programme once a
week at the same day, time and length (Weekly
Recording).
After a timer recording has taken
place
Press
POWER
f
to turn on the VCR. You can
operate your VCR normally.
To stop a started timer recording
Press
POWER
f
.
Recording stops and the VCR turns off.
If it is a Daily or Weekly Recording, future
recordings will be carried out as programmed.
When two programs
overlap
The Program Review screen
will appear with a magenta
line blinking on the newly set
timer recording while the other
overlapped program blinking.
1 Press
PLAY
5 or
STOP
∞ to move the
magenta line among the two overlapping
programs.
2 Press
OK/STATUS
to view
the detail information of the
program you want to change.
3 Go to step 4 through 8 to
modify the selected program.
To cancel any timer recording, press
CLEAR
.
• If you do not modify the overlapping programs, the
VCR will record the earlier program completely.
Only the remaining part of the later program willbe
recorded.
• If the START time for the two programs are the
same, the lower program number will be recorded.
PM
PM
PM
PR CH START STOP DATE
1 12 08:00P 10:00 20/07
2 20 11:00A 11:30 15/10
3 24 03:00P 04:00 10/08
4 45 09:00P 11:00 FRI
5
6
7
8
SELECT: CONFIRM: OK
ONE TIME PROGRAM
PROGRAM 1
/–
START +/– 08 : 00 PM
STOP +/– 10 : 00 PM
REC SPEED SP
DATE +/– 11/23/01
FRIDAY
ERASE: CLEAR END: TIMER
NEXT: OK
PREV:
12
PM
220/75
01.5.11, 4:16 PM
19